manualshive.com logo in svg

Motorola PTP 300 Series, User Manual, Page: 173 / 288

Share
Download
Motorola PTP 300 Series User Manual Download Page 173

 

 

8 Recovery Mode 

 

153

8 Recovery 

Mode 

This section provides instructions to allow users to recover a PTP 300 link.   

The Motorola PTP 300 point-to-point wireless Ethernet bridges have a special mode of 

operation that allows the user to recover a unit from configuration errors or software image 

corruption. 

The following topics are described in this section: 

•

 

8.1 Entering Recovery Mode 

•

 

8.2 Upgrade Software Image 

•

 

8.3 Reset IP & Ethernet Configuration 

•

 

8.4 Erase Configuration 

•

 

8.6 Reboot 

8.1  Entering Recovery Mode 

Recovery mode is entered by depressing the Recovery Switch located on the underside of 

the PIDU Plus while applying mains power, as shown in Section 2.7 “PIDU Plus PTP 

300/500/600 Series” The Recovery Switch should be held in the depressed state for between 

10 and 20 seconds after the application of mains power. The Ethernet LED will flash with 10 

double flashes at power up (following the release of the Recovery switch). 

When in recovery mode the user will be able to access the unit via the Ethernet interface. The 

Ethernet interface will have its IP address set to 169.254.1.1 (or 10.10.10.10 see section 

6.5.10 “Powering Up”). On connection to a unit in recovery mode the following screen is 

displayed (Figure 91): 

Figure 91 - Recovery Mode Warning Page 

 

 

4Gon   www.4Gon.co.uk   [email protected]   Tel: +44 (0)1245 808195   Fax: +44 (0)1245 808299 

Summary of Contents for PTP 300 Series

































































































































































































































































































Reviews:

No comments