manualshive.com logo in svg

Motorola PTP 300 Series, User Manual, Page: 217 / 288

Share
Download
Motorola PTP 300 Series User Manual Download Page 217

 

 

12 Data Rate Calculations 

 

197

12.4  Range Adjustment Curves 

Use these graphs to look up the link Range and find the Throughput Factor that must be 

applied to adjust the 0 km data throughput rates for the required combination of Link Mode 

Optimization (IP or TDM) and Link Range (km). 

Curve A (Figure 120) is used when one of the following conditions applies: 

•

 

Link Symmetry = 3:1 

•

 

Link Symmetry = 1:1 and Link Optimization = IP 

•

 

Link Symmetry = 1:3 

Curve B (Figure 121) is used only when Link Symmetry = 1:1 and Link Optimization = TDM. 

 

Figure 120 – PTP 300 Range Adjustment for Data Rates, Curve A 

 

 

4Gon   www.4Gon.co.uk   [email protected]   Tel: +44 (0)1245 808195   Fax: +44 (0)1245 808299 

Summary of Contents for PTP 300 Series

































































































































































































































































































Reviews:

No comments