Motorola PTP 300 Series User Manual Download Page 240

Page: 240 / 288

16 PTP 300 Reference Information

220

16.1.4 PTP 300 Environmental Specifications

Table 28 – PTP 300 Environmental Specifications

Category

Specification

Temperature

ODU: -40°F (-40°C) to 140°F (+60°C)

PIDU Plus (indoor deployment): 32°F (0°C) to 104

F (+40°C)

PIDU Plus (outdoor deployment within weatherproofed cabinet):
-40°F (-40°C) to 140°F (+60°C)

Wind Loading

150mph Max (242kph). See Section 4.7”Wind Loading” for a full
description.

Humidity

100% Condensing (ODU only)

Waterproof

IP65 (ODU only)

UV Exposure

10 year operational life (UL746C test evidence)

4Gon www.4Gon.co.uk [email protected] Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299

Summary of Contents for PTP 300 Series

































































































































































































































































































Search results

Summary of Contents for PTP 300 Series

Reviews:

Motorola PTP 300 Series, User Manual, Page: 240 / 288

Search results

Summary of Contents for PTP 300 Series

Reviews: