manualshive.com logo in svg

Motorola PTP 300 Series, User Manual, Page: 154 / 288

Share
Download
Motorola PTP 300 Series User Manual Download Page 154

 

 

7 Web Page Reference 

 

134

 

7.9.9  Viewing Historic Spectrum Management Metrics 

Spectrum Management allows the system administrator to view the results of previous 

measurement quantization periods. Holding down the shift key and clicking the appropriate 

channel on the local channel spectrum plots activates this feature. This feature is available on 

both the master and slave web page. 

Figure 74 - Spectrum Management Time Series Plot 

 

Figure 74 shows an example time series plot. A time series plot displays the previous 132 

measurement quantization periods. If the PTP 300 Series Bridge has not been running for 

132 quantization periods then only the number of measurement quantization periods that are 

available are displayed.  

Table 14 - Spectrum Management Time Series Key 

GREEN 

Peak of Means interference measurement 

BLACK 

99.9% percentile of means interference measurement 

BLUE 

Mean of Means interference measurement 

 

4Gon   www.4Gon.co.uk   [email protected]   Tel: +44 (0)1245 808195   Fax: +44 (0)1245 808299 

Summary of Contents for PTP 300 Series

































































































































































































































































































Reviews:

No comments