manualshive.com logo in svg

Motorola PTP 300 Series, User Manual, Page: 51 / 288

Share
Download
Motorola PTP 300 Series User Manual Download Page 51

 

 

4 Planning Considerations 

 

31

 

 

4.3  Radar Avoidance and Bandwidth Operation  

Where regulatory restrictions apply to certain channels these channels are barred. RTTT 

avoidance may be necessary in all channel bandwidths. The number of channels barred is 

dependant on the channel raster selected. For example see the effect of the UK RTTT 

channel restrictions in the 15 MHz bandwidth (Figure 11), where blocks in red indicate 

channels that are barred. Barred channels are indicated by a “No Entry” symbol displayed on 

the “Spectrum Management” web page, see Section 7.9.11 “Spectrum Management Control 

with Radar Avoidance”. 

Figure 11 - 5.8 GHz UK RTTT Channel Avoidance – 15 MHz Channel Bandwidth (Example) 

 

NOTE

    

Radar avoidance requirements in the 5.4 GHz band in the EU is detailed in 
specification EN 301-893 version 

V1.4.1 plus additional requirements shown in the 

OJ of the EC

 and in the US in the specification FCC part 15.407. Radar avoidance at 

5.8 GHz is applicable to EU operation and the requirements are currently as defined 
in EN 302 502. 

4Gon   www.4Gon.co.uk   [email protected]   Tel: +44 (0)1245 808195   Fax: +44 (0)1245 808299 

Summary of Contents for PTP 300 Series

































































































































































































































































































Reviews:

No comments