Home
/
Motorola
/
PTP 300 Series
/
User Manual

Motorola PTP 300 Series, User Manual, Page: 128 / 288

Share

Page: 128 / 288

Motorola PTP 300 Series User Manual Download Page 128

7 Web Page Reference

108

Subnet Mask

A subnet allows the flow of network traffic between hosts to be segregated based on a
network configuration. By organizing hosts into logical groups, subnetting can improve
network security and performance.

Gateway IP Address

The IP address of a computer / router on the current network that acts as a gateway. A
gateway acts as an entrance / exit to packets from / to other networks.

Use VLAN Management Interface

Controls whether the management interfaces (HTTP/SNMP/SMTP/SNTP) use a VLAN.
Selecting this option presents the user with extra fields in which to enter the Management
VLAN ID, Priority and whether to validate the VLAN ID. If the user modifies this control, a
warning dialog is displayed see Figure 57.

Telecoms Interface

This allows the activation of the PTP 300 Series bridge telecoms interface. The selection
options are None, E1 or T1.

Figure 57 - VLAN Warning

Once complete, click the ‘Submit Internet Protocol Configuration’ button or the ‘Next’ link.

4Gon www.4Gon.co.uk [email protected] Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299

«
...
126
127
128
129
130
...
»

Summary of Contents for PTP 300 Series

































































































































































































































































































Reviews:

No comments