manualshive.com logo in svg

Motorola PTP 300 Series, User Manual, Page: 136 / 288

Share
Download
Motorola PTP 300 Series User Manual Download Page 136

 

 

7 Web Page Reference 

 

116

 

7.7.5  Installation Wizard Step 3 - Confirm Configuration 

Step 3 of the installation wizard requires the installer to confirm the wireless configuration 

parameters.  Figure 61 is an example of the Confirm Configuration screen. The screen 

contents vary depending upon the product variant and configuration options selected. 

Figure 61 – Installation Wizard Confirm Configuration 

 

If the settings are correct and appropriate, click the “Confirm Configuration, Arm Installation 

and Reboot” button. The user will now be prompted to confirm the action (Figure 62).  

4Gon   www.4Gon.co.uk   [email protected]   Tel: +44 (0)1245 808195   Fax: +44 (0)1245 808299 

Summary of Contents for PTP 300 Series

































































































































































































































































































Reviews:

No comments