manualshive.com logo in svg

Motorola PTP 300 Series, User Manual, Page: 119 / 288

Share
Download
Motorola PTP 300 Series User Manual Download Page 119

 

 

7 Web Page Reference 

 

99

7.6  Statistics  

The System Statistics page (Figure 53) displays some key statistics of the Ethernet Bridge 

and the underlying wireless performance.  

The numbers in brackets display the number of packets received since the last page refresh. 

Figure 53 - System Statistics Page 

 

The System Statistics page contains the following fields: 

Wireless Tx Packets 

This displays the total number of good packets the bridge has sent for transmission by the 
wireless interface. 

Wireless Rx Packets 

This displays the total number of good packets the bridge has received from the wireless 
interface. 

4Gon   www.4Gon.co.uk   [email protected]   Tel: +44 (0)1245 808195   Fax: +44 (0)1245 808299 

Summary of Contents for PTP 300 Series

































































































































































































































































































Reviews:

No comments