Mitsubishi Electric PUHY-(E)P300 Page 47 Service Handbook Download

Page: 47 / 302

- 38 -

[

Restrictions ]

HWE07010

[6] An Example of a System to which an M-NET Remote Controller is connected

(1) Sample control wiring

(2) Cautions

1) M-NET remote controller and MA remote controller can-

not both be connected to the same group of indoor units.

2) No more than 3 M-NET remote controllers can be con-

nected to a group of indoor units.

3) Do not connect the terminal blocks (TB5) on the indoor

units that are connected to different outdoor units with
each other.

4) Replace the power jumper connector of the control board

from CN41 to CN40 on only one of the outdoor units.

5) Provide an electrical path to ground for the S terminal on

the terminal block for centralized control on only one of
the outdoor units.

6) A transmission booster must be connected to a system

in which the total number of connected indoor units ex-
ceeds 20.

7) A transmission booster is required in a system to which

more than 16 indoor including one or more indoor units
of the 200 model or above are connected.

8) When a power supply unit is connected to the transmis-

sion line for centralized control, leave the power jumper
connector on CN41 as it is (factory setting).

(3) Maximum allowable length

1) Indoor/outdoor transmission line

Same as [5] 3.

2) Transmission line for centralized control

Same as [5] 4.

3) M-NET remote controller wiring

Maximum overall line length

(0.3 to 1.25mm

[AWG22 to 16])

m1 10m [32ft]

m2+m3 10m [32ft]

If the standard-supplied cable must be extended, use a

cable with a diameter of 1.25mm

[AWG16]. The section

of the cable that exceeds 10m [32ft] must be included in

the maximum indoor-outdoor transmission line distance

described in (1).

When connected to the terminal block on the Simple re-

mote controller, use cables that meet the following cable

size specifications: 0.75 - 1.25 mm

[AWG18-14].

TB5

TB15

1 2

TB5

TB15

1 2

TB5

1 2

TB15

TB5

TB15

1 2

TB5

TB15

1 2

TB5

TB15

1 2

A B

101

A B

102

A B

103

Group

M1 M2

L12

L11

L22

L21

L31

A B S

L32

Note1

System controller

Interlock operation with
the ventilation unit

TB3

TB7

OS1

TB3

TB7

OS2

TB3

TB7

M1 M2

TB3

TB7

OS1

TB3

TB7

OS2

TB3

TB7

M1 M2

Leave the male

connector on

CN41 as it is.

SW2-1 OFF ON

Leave the male

connector on

CN41 as it is.

SW2-1 OFF ON

Leave the male

connector on

CN41 as it is.

SW2-1 OFF ON

Leave the male

connector on

CN41 as it is.

SW2-1 OFF ON

Leave the male

connector on

CN41 as it is.

SW2-1 OFF ON

CN41 CN40 Replace

Connect

104

A B

154

A B

106

A B

Note1 When only the LM adapter is connected,
leave SW2-1 to OFF (as it is).
Note2 LM adapters require the power supply
capacity of single-phase AC 208/230V.

Not
Connect

Summary of Contents for PUHY-(E)P300















































































































































































































































































































Search results

Summary of Contents for PUHY-(E)P300

Reviews:

Related manuals for PUHY-(E)P300

Brands by name

Popular brands

Mitsubishi Electric PUHY-(E)P300, Service Handbook

Search results

Summary of Contents for PUHY-(E)P300

Reviews:

Related manuals for PUHY-(E)P300

Brands by name

Popular brands