Mitsubishi Electric PUHY-(E)P300 Page 186 Service Handbook Download

Page: 186 / 302

[

Troubleshooting ]

- 177 -

HWE07010

1. Error

Code

Overcurrent error due to short-circuited motor (Detail code 105)

2. Error

definition and error detection method

When a short is detected on the load side just before starting the inverter operation.

3. Cause, Check method and remedy

In the case of 4250

In the case of 4255

Refer to section - 6 - "Inverter" under part [4] "Trouble shooting principal parts" for error codes related to the

inverter.(page 232)

1. Error

Code

Heatsink overheat protection before startup

2. Error

definition and error detection method

The heatsink temperature (THHS) remains at or above 100°C [212°F] for 10 minutes or more at inverter startup.

3. Cause, check method and remedy

Same as 4230 error

4250

4255

Cause

Check method and remedy

(1)

Short - circuited compressor

Refer to 9 [4] - 6 - (2) [2].(page 234)

(2)

Output wiring

Check for a short circuit.

Cause

Check method and remedy

(1)

Short - circuited fan motor

Refer to 9 [4] - 6 - (2) [5].(page 235)

(2)

Output wiring

Check for a short circuit.

4260

Summary of Contents for PUHY-(E)P300















































































































































































































































































































Search results

Summary of Contents for PUHY-(E)P300

Reviews:

Related manuals for PUHY-(E)P300

Brands by name

Popular brands

Mitsubishi Electric PUHY-(E)P300, Service Handbook

Search results

Summary of Contents for PUHY-(E)P300

Reviews:

Related manuals for PUHY-(E)P300

Brands by name

Popular brands