Mitsubishi Electric PUHY-(E)P300 Page 195 Service Handbook Download

Page: 195 / 302

[

Troubleshooting ]

- 186 -

HWE07010

1. Error

Code

Transmission circuit bus-busy

2. Error

definition and error detection method

Generated error when the command cannot be transmitted for 4-10 minutes in a row due to bus-busy

Generated error when the command cannot be transmitted to the transmission line for 4-10 minutes in a row due to noise

The address/attribute appeared on the display on the remote controller indicates the controller where an error oc-

curred.

3. Cause, check method and remedy

1. Error

Code

Communication error with the transmission processor

2. Error

definition and error detection method

Communication error between the main microcomputer on the indoor unit board and the microcomputer for transmission

The address/attribute appeared on the display on the remote controller indicates the controller where an error oc-

curred.

3. Cause, check method and remedy

6603

Cause

Check method and remedy

(1)

The transmission processor cannot be transmit-

ted as the short-wavelength voltage like noise ex-

ists consecutively on the transmission line.

No noise indicates that the error source controller is a fail-

ure. If noise exists, investigate the noise.

-> No noise indicates that the error source controller is a

failure.

-> If noise exists, investigate the noise.

(2)

Error source controller failure

6606

Cause

Check method and remedy

(1)

Data is not properly transmitted due to accidental

erroneous operation of the controller of the error

source.

Turn off the power source of the outdoor and the indoor

units.(When the power source is turned off separately, the

microcomputer will not be reset, and the error will not be

corrected.)

-> If the same error occurs, the error source controller is

a failure.

(2)

Error source controller failure

Summary of Contents for PUHY-(E)P300















































































































































































































































































































Search results

Summary of Contents for PUHY-(E)P300

Reviews:

Related manuals for PUHY-(E)P300

Brands by name

Popular brands

Mitsubishi Electric PUHY-(E)P300, Service Handbook

Search results

Summary of Contents for PUHY-(E)P300

Reviews:

Related manuals for PUHY-(E)P300

Brands by name

Popular brands