Mitsubishi Electric PUHY-(E)P300 Page 100 Service Handbook Download

Page: 100 / 302

[

VII

Control ]

- 91 -

HWE07010

(3) Stopping the defrost operation

The defrost cycle ends when 12 minutes have passed since the beginning of the cycle, or when the pipe temperature (TH3),

in the following table, or above has been continuously detected for 4 minutes.

Defrost operation will not stop its operation for 2 minutes once started unless the piping temperature exceeds 25°C [77°F]

within 2 minutes, in which case the operation will stop.

In the multiple-outdoor-unit system, defrosting is stopped on all units at the same time.

(4) Problems during defrost operation

If a problem is detected during defrost operation, the operation will be stopped, and the defrost prohibition time based on the

integrated compressor operation time will be set to 20 minutes.

(5) Change in the number of operating indoor units during defrost operation

Even when there is a change in the number of operating indoor units during defrost operation, the operation will continue, and

an adjustment will be made after the completion of the defrost operation.

Defrost operation will be continued, even if the indoor units stop or under the Thermo-OFF conditions until it has run its course.

-8- Refrigerant Recovery Control

Recovery of refrigerant is performed during heating operation to prevent the refrigerant from accumulating inside the unit while

it is stopped (unit in fan mode), or inside the indoor unit that is in cooling mode or in heating mode with thermo off. It is also

performed during cooling operation to prevent an excessive amount of refrigerant from accumulating in the outdoor heat ex-

changer.

It is also performed during cooling operation to prevent an excessive amount of refrigerant from accumulating in the outdoor

heat exchanger.

(1) During heating operation

Starting refrigerant recovery mode

The refrigerant recovery mode in heating starts when all of the following three conditions are met:

15 minutes have passed since the completion of previous refrigerant recovery.

TH4 > 115°C [239°F]

Frequencies below 50 Hz

Refrigerant recovery

1) Refrigerant is recovered with the LEV on the applicable indoor unit (unit under stopping mode, fan mode, cooling, heating with

thermo off) being opened for 30 seconds.

2) Periodic capacity control of the outdoor units and periodic LEV control of the indoor units will be suspended during refrigerant

recovery operation; they will be performed after the recovery has been completed.

Model

TH3

SW3 - 3 OFF

SW3 - 3 ON

200 model

10°C [50°F]

15°C [59°F]

250 model

10°C [50°F]

15°C [59°F]

300 model

10°C [50°F]

15°C [59°F]

350 model

7°C [45°F]

12°C [54°F]

400 model

7°C [45°F]

12°C [54°F]

450 mode;

7°C [45°F]

12°C [54°F]

Opening of LEV during refrigerant recovery
Opening of indoor unit LEV: 400 pulses

Initial opening of LEV

Start

Finish

30 seconds

Summary of Contents for PUHY-(E)P300















































































































































































































































































































Search results

Summary of Contents for PUHY-(E)P300

Reviews:

Related manuals for PUHY-(E)P300

Brands by name

Popular brands

Mitsubishi Electric PUHY-(E)P300, Service Handbook

Search results

Summary of Contents for PUHY-(E)P300

Reviews:

Related manuals for PUHY-(E)P300

Brands by name

Popular brands