Mitsubishi Electric PUHY-(E)P300 Page 28 Service Handbook Download | Manualshive

Page: 28 / 302

background image

[

II

Restrictions ]

- 19 -

HWE07010

GB

[2] Types and Maximum allowable Length of Cables

1. Wiring

work

(1) Notes

1) Have all electrical work performed by an authorized electrician according to the local regulations and instructions in this man-

ual.

2) Install external transmission cables at least 5cm [1-31/32"] away from the power supply cable to avoid noise interference.

(Donot put the control cable and power supply cable in the same conduit tube.)

3)   Provide grounding for the outdoor unit as required.
4)   Run the cable from the electric box of the indoor or outdoor unit in such way that the box is accessible for servicing.
5)   Do not connect power supply wiring to the terminal block for transmission line. Doing so will damage the electronic compo-

nents on the terminal block.

6) Use 2-core shielded cables as transmission cables.

Use a separate 2-core control cable for each refrigerant system. Do not use a single multiple-core cable to connect indoor
units that belong to different refrigerant systems. The use of a multiple-core cable may result in signal transmission errors and
malfunctions.

(2) Control wiring

Different types of control wiring are used for different systems.
Refer to section "[5] An Example of a System to which an MA Remote Controller is connected - [7] An Example of a System
to which both MA Remote Controller and M-NET Remote Controller are connected" before performing wiring work.

Types and maximum allowable length of cables

Control lines are categorized into 2 types: transmission line and remote controller line.
Use the appropriate type of cables and observe the maximum allowable length specified for a given system. If a given system
has a long transmission line or if a noise source is located near the unit, place the unit away from the noise source to reduce
noise interference.

1) M-NET transmission line

Cable type

Facility
type

All facility types

Type

Shielded cable CVVS, CPEVS, MVVS

Number of
cores

2-core cable

Cable size

Larger than 1.25mm

2

[AWG16]

Maximum transmission
line distance between the
outdoor unit and the far-
thest indoor unit

200 m [656ft] max.

Maximum transmission
line distance for central-
ized control and Indoor/
outdoor transmission line
(Maximum line distance
via outdoor unit)

500 m [1640ft] max.
*The maximum overall line length from the power supply unit on the transmission lines for
centralized control to each outdoor unit or to the system controller is 200m [656ft] max.

TB

3

TB

7

TB

3

TB

7

TB

3

TB

3

TB

7

TB

7

TB

3

TB

7

TB

3

TB

7

TB

3

TB

7

TB

3

TB

7

TB

3

TB

3

TB

7

TB

7

TB

3

TB

7

TB

3

TB

7

2-core shielded cable

2-core shielded cable

Indoor unit

Outdoor unit

TB3: Terminal block for indoor-outdoor transmission line TB7: Terminal block for centralized control

Remote Controller

Indoor unit

Outdoor unit

Remote Controller

multiple-core cable

«
...
26
27
28
29
30
...
»

Summary of Contents for PUHY-(E)P300















































































































































































































































































































Reviews:

No comments

Related manuals for PUHY-(E)P300

Brand: NEC Pages: 15

Brand: Fellowes Pages: 8

Brand: Samsung Pages: 16

Brand: Guzzanti Pages: 140

Brand: WELLTEC Pages: 43

Brand: Zibro Pages: 2

Brand: Daikin Pages: 92

Brand: Arctic King Pages: 38

23-11-2228N-004

Brand: Maytag Pages: 24

Brand: UNITED Pages: 36

Brand: Daikin Pages: 20

Brand: Daikin Pages: 36

Brand: Carrier Pages: 13

Brand: Rasonic Pages: 2

Brand: Argo Pages: 40

Brand: Ivation Pages: 3

Brand: OVALAIR Pages: 13

Brand: Daikin Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands