Mitsubishi Electric PUHY-(E)P300 Page 199 Service Handbook Download

Page: 199 / 302

[

Troubleshooting ]

- 190 -

HWE07010

1. Error

Code

No ACK abnormality

2. Error

definition and error detection method

The error is detected when no acknowledgement (ACK signal) is received after the transmission. (eg. When the data is trans-

mitted six times in a row with 30 seconds interval, the error is detected on the transmission side.)

The address/attribute appeared on the display on the remote controller indicates the controller which did not provide

the response (ACK).

3. System

configuration

(2) Grouping of units in a system with multiple outdoor units

6607

Error

source

address

Error display

Detection

method

Cause

Check method and remedy

M-NET re-

mote con-

troller

(RC)

M-NET re-

mote controller

(RC)

MA remote

controller (MA)

No acknowl-

edgement

(ACK) at IC

transmission to

(1)

Same causes as (1) - (4) for

system with one outdoor unit

Turn off the power source of

LOSSNAY for 5 or more min-

utes, and turn it on again. If the

error is accidental, it will run

normally.If not, check the

cause 2).

(2)

Disconnection or short circuit

of the transmission line for

the outdoor unit on the termi-

nal block for centralized con-

trol line connection (TB7)

Check the causes of (1) - (5). If

the cause is found, correct it. If

no cause is found, check 3).

(3)

When multiple outdoor units

are connected and the power

source of one of the outdoor

units has been shut off.

Same cause as that for indoor

unit described in 3)

(4)

The male power supply con-

nector of the outdoor unit is

not connected to the female

power supply switch connec-

tor (CN40).

(5)

The male power supply con-

nectors on 2 or more outdoor

units are connected to the fe-

male power supply switch

connector (CN40) for central-

ized control.

If the problem recurs after

normal operation is restored,

the problem is caused by one

of the following factors:

Total capacity error

(7100)

Capacity code setting

error (7101)

Error in the number of

connected units (7102)

Address setting error

(7105)

Summary of Contents for PUHY-(E)P300















































































































































































































































































































Search results

Summary of Contents for PUHY-(E)P300

Reviews:

Related manuals for PUHY-(E)P300

Brands by name

Popular brands

Mitsubishi Electric PUHY-(E)P300, Service Handbook

Search results

Summary of Contents for PUHY-(E)P300

Reviews:

Related manuals for PUHY-(E)P300

Brands by name

Popular brands