manualshive.com logo in svg

Mitsubishi Electric PUHY-(E)P300, Service Handbook

The Mitsubishi Electric PUHY-(E)P300 Service Handbook is a comprehensive manual designed to assist you in understanding and maintaining your PUHY-(E)P300 unit. This user-friendly manual is available for free download on our website, ensuring easy access to essential information and guidelines. Enhance your product knowledge and maximize performance effortlessly with this valuable resource.

Share
Download
background image

[ 

IX 

 Troubleshooting ] 

- 197 -

HWE07010

GB

1. Error 

Code

MA communication error or start bit detection error

2. Error 

definition and error detection method

Œ

Communication between the MA remote controller and the indoor unit is not done properly.

Œ

No proper data has been received for 2 minutes.

3. Cause

1)   Contact failure of the remote controller lines of MA remote controller or the indoor unit.
2)   All the remote controllers are set to SUB.
3)   Failure to meet wiring regulations

Œ

Wire length

Œ

Wire size

Œ

Number of remote controllers

Œ

Number of indoor units

4)   The remote controller is removed after the installation without turning the power source off.
5)   Noise interference on the remote controller transmission lines
6)   Faulty circuit that is on the indoor board and performs transmission/ reception of the signal from the remote controller
7)   Problems with the circuit on the remote controller that sends or receives the signals from the remote controller

4.  Check method and remedy

1)   Check for disconnected or loose transmission lines for the indoor units or MA remote controllers.
2)   Confirm that the power is supplied to the main power source and the remote controller line.
3)   Confirm that MA remote controller's capacity limit is not exceeded.
4)   Check the sub/main setting of the MA remote controllers.One of them must be set to MAIN.
5)   Diagnose the remote controller (described in the remote controller installation manual).

[OK]: no problems with the remote controller (check the wiring regulations)

[NO]: Replace the MA remote controller.

[6832, 6833, ERC]: Due to noise interference <Go to 5)>

6)   Check wave shape/noise on MA remote controller line by following "IX [3] Investigation of Transmission Wave Shape/

Noise".(page 219)

7)   When no problems are found with items 1 through 6, replace the indoor unit board or the MA remote controller.

The following status can be confirmed on LED1 and 2 on the indoor unit board.

Œ

If LED1 is lit, the main power source of the indoor unit is turned on

Œ

If LED2 is lit, the MA remote controller line is being powered.

6834

Summary of Contents for PUHY-(E)P300















































































































































































































































































































Reviews:

No comments

Related manuals for PUHY-(E)P300

Acekool CW1 User Manual preview
CW1
Brand: Acekool Pages: 24
Houghton BELAIRE HB3200 Owner'S Manual preview
BELAIRE HB3200
Brand: Houghton Pages: 25
INVENTOR V5MFI32-60 User & Installation Manual preview
V5MFI32-60
Brand: INVENTOR Pages: 136
Orbegozo FDI 124 Installation Manual preview
FDI 124
Brand: Orbegozo Pages: 143
Bard Q24A1 Installationair conditioner Instructions Manual preview
Q24A1 Installationair conditioner
Brand: Bard Pages: 38
Clatronic CL 3542 Instruction Manual preview
CL 3542
Brand: Clatronic Pages: 62
edc LIMPET Installation And Operating Manual preview
LIMPET
Brand: edc Pages: 46
Daikin RKS20E2V1B Installation Manual preview
RKS20E2V1B
Brand: Daikin Pages: 14
Movincool CLIMATE PRO X14 Service Manual preview
CLIMATE PRO X14
Brand: Movincool Pages: 58
DeDietrich MOSE 20 User Manual preview
MOSE 20
Brand: DeDietrich Pages: 12
Fedders 23-23-0381N-002 s Installation & Operation Manual preview
23-23-0381N-002 s
Brand: Fedders Pages: 20
Samsung RAC Series Technical Data Book preview
RAC Series
Brand: Samsung Pages: 49
Momax AP7S Instruction Manual preview
AP7S
Brand: Momax Pages: 41
YILKAR Montaj Talimati YK 190 MB L Installation Instruction preview
Montaj Talimati YK 190 MB L
Brand: YILKAR Pages: 84
Gree GMV-ND100T/C-T Owner'S Manual preview
GMV-ND100T/C-T
Brand: Gree Pages: 27
Cooline PT036 Installation, Operation & Maintenance Manual preview
PT036
Brand: Cooline Pages: 31
Wow WAC 1200PLUS Instruction Manual preview
WAC 1200PLUS
Brand: Wow Pages: 68
Daikin Super Multi NX CTXG50JV1BS Installation Manual preview
Super Multi NX CTXG50JV1BS
Brand: Daikin Pages: 16

Brands by name

Popular brands

Load more brands