manualshive.com logo in svg

Mitsubishi Electric PUHY-(E)P300, Service Handbook, Page: 110 / 302

Share
Download
Mitsubishi Electric PUHY-(E)P300 Service Handbook Download Page 110

[ 

VII 

 Control ] 

- 101 -

HWE07010

GB

2.  Operations in each mode
(1) Cooling operation

*Note 1. The indoor fan operates at the set notch under cooling mode regardless of the ON/OFF state of the thermostat.

Cooling operation

Test run mode 

ON

Thermostat ON

3-minute restart 

prevention

*Note 1

YES

YES

YES

NO

NO

NO

4-way valve OFF

1. Inverter frequency control
2. Indoor unit LEV, LEV1 control
    LEV2a, LEV2b fully opened
3. Solenoid valve control
4. Outdoor unit fan control
5. 72C control

Normal operation

During test run mode

Unit in the stopped state

Indoor unit fan 
operation

1. Inverter output  0Hz
2. Indoor unit LEV1, LEV1
    LEV2a, LEV2b rated opening
3. All solenoid valves OFF
4. Outdoor unit fan stop
5. 72C OFF

Summary of Contents for PUHY-(E)P300















































































































































































































































































































Reviews:

No comments