Mitsubishi Electric PUHY-(E)P300 Page 184 Service Handbook Download

Page: 184 / 302

[

Troubleshooting ]

- 175 -

HWE07010

1. Error

Code

Overload protection

2. Error

definition and error detection method

If the output current of "(Iac) >Imax (Arms)" or "THHS > 95°C [203°F] " is continuously detected for 10 minutes or more during

inverter operation.

3. Cause, check method and remedy

Refer to section - 6 - "Inverter" under part [4] "Trouble shooting principal parts" for error codes related to the

inverter.(page 232)

1. Error

Code

IPM error (Detail code 101)

2. Error

definition and error detection method

In the case of 4250

Overcurrent is detected by the overcurrent detection resistor (RSH) on the inverter board.

In the case of 4255

IPM error signal is detected.

3. Cause, check method and remedy

In the case of 4250

In the case of 4255

Refer to section - 6 - "Inverter" under part [4] "Trouble shooting principal parts" for error codes related to the

inverter.(page 232)

4240

Cause

Check method and remedy

(1)

Air passage blockage

Check that the heat sink cooling air passage is not blocked

(2)

Power supply environment

Power supply voltage is 342 V or above.

(3)

Inverter failure

Refer to 9 [4] - 6 -.(page 232)

(4)

Compressor failure

Check that the compressor has not overheated during operation.

-> Check the refrigerant circuit (oil return section).

Refer to 9 [4] - 6 - (2)[2].(page 234)

4250

4255

Cause

Check method and remedy

(1)

Inverter output related

Refer to 9 [4] - 6 - (2) [1] - [4].(page 234)

Check the IGBT module resistance value of the inverter board, if no

problems are found.

(Refer to the Trouble shooting for IGBT module)

Cause

Check method and remedy

(1)

Fan motor abnormality

Refer to 9 [4] - 6 - (2) [5].(page 235)

(2)

Fan board failure

Refer to 9 [4] - 6 - (2) [6].(page 235)

Imax(Arms)

Model

P200, P250

P300 - P450

Summary of Contents for PUHY-(E)P300















































































































































































































































































































Search results

Summary of Contents for PUHY-(E)P300

Reviews:

Related manuals for PUHY-(E)P300

Brands by name

Popular brands

Mitsubishi Electric PUHY-(E)P300, Service Handbook

Search results

Summary of Contents for PUHY-(E)P300

Reviews:

Related manuals for PUHY-(E)P300

Brands by name

Popular brands