Mitsubishi Electric PUHY-(E)P300 Page 193 Service Handbook Download

Page: 193 / 302

[

Troubleshooting ]

- 184 -

HWE07010

1. Error

Code

Address overlap

2. Error

definition and error detection method

An error in which signals from more than one indoor units with the same address are received

The address and attribute that appear on the remote controller indicate the controller that detected the error.

3. Cause, check method and remedy

1. Error

Code

Unset polarity

2. Error

definition and error detection method

The error detected when transmission processor cannot distinguish the polarities of the M-NET transmission line.

3. Cause, check method and remedy

6600

Cause

Check method and remedy

Two or more of the following have the same address:

Outdoor units, indoor units, LOSSNAY units, control-

lers such as M-NET remote controllers.

6600 appears on the remote controller

"01" Unit #01 detected the error.

Two or more units in the system have 01 as their ad-

dress.

Find the unit that has the same address as that of the

error source.

Once the unit is found, correct the address. Then,

turn off the outdoor units, indoor units, and LOSS-

NAY units, keep them all turned off for at least five

minutes, and turn them back on.

6601

Cause

Check method and remedy

(1)

No voltage is applied to the M-NET transmission line

that G(B)-50A is connected to.

Check if power is supplied to the M-NET transmission

line of the G(B)-50A, and correct any problem found.

(2)

M-NET transmission line to which G(B)-50A is con-

nected is short-circuited.

Summary of Contents for PUHY-(E)P300















































































































































































































































































































Search results

Summary of Contents for PUHY-(E)P300

Reviews:

Related manuals for PUHY-(E)P300

Brands by name

Popular brands

Mitsubishi Electric PUHY-(E)P300, Service Handbook

Search results

Summary of Contents for PUHY-(E)P300

Reviews:

Related manuals for PUHY-(E)P300

Brands by name

Popular brands