Mitsubishi Electric PUHY-(E)P300 Page 222 Service Handbook Download

Page: 222 / 302

[

Troubleshooting ]

- 213 -

HWE07010

In case of M-NET remote controller

1. Phenomena

"88" appears on the remote controller when the address is registered or confirmed.

2. Cause, check method and remedy

Cause

Check method and remedy

An error occurs when the address is registered or con-

firmed. (common)

A wrong address is set to the unit to be coupled.

(1)

Confirm the address of unit to be coupled.

The transmission line of the unit to be coupled is dis-

connected or is not connected.

(2)

Check the connection of transmission line.

Circuit board failure of the unit to be coupled

(3)

Check voltage of the terminal block for transmission

line of the unit to be coupled.

Normal if voltage is between DC17 and 30V.

Improper transmission line work

Check (5) in case other than 1).

Generates at interlocking registration between LOSS-

NAY and the indoor unit

The power of LOSSNAY is OFF.

(5)

Check for the main power of LOSSNAY.

Generates at confirmation of controllers used in the

system in which the indoor units connected to different

outdoor units are grouped

The power of the outdoor unit to be confirmed has

been cut off.

(6)

Check the power supply of the outdoor unit which is

coupled with the unit to be confirmed.

The power of the outdoor unit to be confirmed has

been cut off.

(7)

Check that the transmission line for centralized

control (TB7) of the outdoor unit is not disconnect-

ed.

When the indoor units connected to different outdoor

units are grouped without MELANS, the male power

supply connector is not connected to the female

power supply switch connector (CN40) for the trans-

mission line for centralized control.

(8)

Check voltage of the transmission line for central-

ized control.

The male power supply connectors on 2 or more out-

door units are connected to the female power supply

switch connector (CN40) for the transmission line for

centralized control.

Normal when voltage is between 10V and 30V

10.

In the system to which MELANS is connected, the

male power supply connector is connected to the fe-

male power supply switch connector (CN40) for the

transmission line for centralized control.

Check 8 - 11 described on the left in case other than

1).

11.

Short circuit of the transmission line for centralized

control

Summary of Contents for PUHY-(E)P300















































































































































































































































































































Search results

Summary of Contents for PUHY-(E)P300

Reviews:

Related manuals for PUHY-(E)P300

Brands by name

Popular brands

Mitsubishi Electric PUHY-(E)P300, Service Handbook

Search results

Summary of Contents for PUHY-(E)P300

Reviews:

Related manuals for PUHY-(E)P300

Brands by name

Popular brands