Mitsubishi Electric PUHY-(E)P300 Service Handbook Download Page 169

Page: 169 / 302

[

Troubleshooting ]

- 160 -

HWE07010

1. Error

Code

Abnormal low pressure

2. Error

definition and error detection method

When starting the compressor from Stop Mode for the first time if low pressure reads 0.098MPa [14psi] immediately

before start-up, the operation immediately stops.

3. Cause, check method and remedy

1301

Cause

Check method and remedy

(1)

Inner pressure drop due to a leakage.

Refer to the section on troubleshooting the low pressure

sensor.(page 223)

(2)

Low pressure sensor failure

(3)

Short-circuited pressure sensor cable due to

torn outer rubber

(4)

A pin on the male connector is missing.

(5)

Disconnected wire

(6)

Failure of the low pressure input circuit on the

controller board

Summary of Contents for PUHY-(E)P300















































































































































































































































































































Search results

Summary of Contents for PUHY-(E)P300

Reviews:

Mitsubishi Electric PUHY-(E)P300, Service Handbook, Page: 169 / 302

Search results

Summary of Contents for PUHY-(E)P300

Reviews: