Mitsubishi Electric PUHY-(E)P300 Page 49 Service Handbook Download

Page: 49 / 302

- 40 -

[

Restrictions ]

HWE07010

[7] An Example of a System to which both MA Remote Controller and M-NET Remote Controller are connected

(1) Sample control wiring

(2) Cautions

1) Be sure to connect a system controller.
2) M-NET remote controller and MA remote controller can-

not both be connected to the same group of indoor units.

3) Assign to the indoor units connected to the MA remote

controller addresses that are smaller than those of the in-
door units that are connected to the M-NET remote con-
troller.

4) No more than 2 M-NET remote controllers can be con-

nected to a group of indoor units.

5) No more than 2 MA remote controllers can be connected

to a group of indoor units.

6) Do not connect the terminal blocks (TB5) on the indoor

units that are connected to different outdoor units with
each other.

7) Replace the power jumper connector of the control board

from CN41 to CN40 on only one of the outdoor units.

8) Provide an electrical path to ground for the S terminal on

the terminal block for centralized control on only one of
the outdoor units.

9) A transmission booster must be connected to a system

in which the total number of connected indoor units ex-
ceeds 20.

10) A transmission booster is required in a system to which

more than 16 indoor including one or more indoor units
of the 200 model or above are connected.

11) When a power supply unit is connected to the transmis-

sion line for centralized control, leave the power jumper
connector on CN41 as it is (factory setting).

(3) Maximum allowable length

1) Indoor/outdoor transmission line

Same as [5] 3.

2) Transmission line for centralized control

Same as [5] 4.

3) MA remote controller wiring

Same as [5] 1.

4) M-NET remote controller wiring

Same as [5] 1.

TB5 TB15

1 2

TB5 TB15

1 2

TB5 TB15

1 2

106

TB5 TB15

1 2

A B

TB5

1 2

TB15

TB5 TB15

1 2

104

A B

L11 L12

L21 L22

TB3

TB7

TB3

TB7

TB3

TB7

M1 M2

TB3

TB7

OS1

TB3

TB7

OS2

TB3

TB7

M1 M2

L31

A B S

L32

M1 M2

SW2-1 OFF ON

Leave the male

connector on

CN41 as it is.

SW2-1 OFF ON

Leave the male

connector on

CN41 as it is.

OS1

OS2

CN41 CN40 Replace

SW2-1 OFF ON

Group Group

Group

SW2-1 OFF ON

Leave the male

connector on

CN41 as it is.

SW2-1 OFF ON

Leave the male

connector on

CN41 as it is.

SW2-1 OFF ON

Leave the male

connector on

CN41 as it is.

Note1

System controller

Note1 When only the LM adapter is connected,
leave SW2-1 to OFF (as it is).

Note2 LM adapters require the power supply
capacity of single-phase AC 208/230V.

Connect

M1 M2

Not
Connect

Summary of Contents for PUHY-(E)P300















































































































































































































































































































Search results

Summary of Contents for PUHY-(E)P300

Reviews:

Related manuals for PUHY-(E)P300

Brands by name

Popular brands

Mitsubishi Electric PUHY-(E)P300, Service Handbook

Search results

Summary of Contents for PUHY-(E)P300

Reviews:

Related manuals for PUHY-(E)P300

Brands by name

Popular brands