manualshive.com logo in svg

Mitsubishi Electric PUHY-(E)P300, Service Handbook

The Mitsubishi Electric PUHY-(E)P300 Service Handbook is a comprehensive manual designed to assist you in understanding and maintaining your PUHY-(E)P300 unit. This user-friendly manual is available for free download on our website, ensuring easy access to essential information and guidelines. Enhance your product knowledge and maximize performance effortlessly with this valuable resource.

Share
Download
background image

[ 

IX 

 Troubleshooting ]

- 196 -

HWE07010

GB

1. Error 

Code

MA communication error or no reception error

2. Error 

definition and error detection method

Œ

Communication between the MA remote controller and the indoor unit is not done properly. 

Œ

No proper data has been received for 3 minutes.

3. Cause

1)   Contact failure of the remote controller lines of MA remote controller or the indoor unit.
2)   All the remote controllers are set to SUB.
3)   Failure to meet wiring regulations

Œ

Wire length

Œ

Wire size

Œ

Number of remote controllers

Œ

Number of indoor units

4)   The remote controller is removed after the installation without turning the power source off.
5)   Noise interference on the remote controller transmission lines
6)   Faulty circuit that is on the indoor board and performs transmission/ reception of the signal from the remote controller
7)   Problems with the circuit on the remote controller that sends or receives the signals from the remote controller

4.  Check method and remedy

1)   Check for disconnected or loose transmission lines for the indoor units or MA remote controllers.
2)   Confirm that the power is supplied to the main power source and the remote controller line.
3)   Confirm that MA remote controller's capacity limit is not exceeded.
4)   Check the sub/main setting of the MA remote controllers.One of them must be set to MAIN.
5)   Diagnose the remote controller (described in the remote controller installation manual).

[OK]: no problems with the remote controller (check the wiring regulations)

[NO]: Replace the MA remote controller.

[6832, 6833, ERC]: Due to noise interference <Go to 5)>

6)   Check wave shape/noise on MA remote controller line by following "IX [3] Investigation of Transmission Wave Shape/

Noise".(page 219)

7)   When no problems are found with items 1 through 6, replace the indoor unit board or the MA remote controller.

The following status can be confirmed on LED1 and 2 on the indoor unit board.

Œ

If LED1 is lit, the main power source of the indoor unit is turned on.

Œ

If LED2 is lit, the MA remote controller line is being powered.

6831

Summary of Contents for PUHY-(E)P300















































































































































































































































































































Reviews:

No comments

Related manuals for PUHY-(E)P300

Saneo BFK1901R Manual preview
BFK1901R
Brand: Saneo Pages: 49
Valeo DD 430 Owner'S Manual preview
DD 430
Brand: Valeo Pages: 60
Ozontech XT - series User Manual preview
XT - series
Brand: Ozontech Pages: 11
Pump House PAC-C-12 Owner'S Manual preview
PAC-C-12
Brand: Pump House Pages: 17
Prem-I-Air EH1230 User Manual preview
EH1230
Brand: Prem-I-Air Pages: 12
eeese Freia 2515 User Manual preview
Freia 2515
Brand: eeese Pages: 94
Daikin RXS50J2V1B Installation Manual preview
RXS50J2V1B
Brand: Daikin Pages: 14
Cellartec CT12TSD Installation, Operation & Care Manual preview
CT12TSD
Brand: Cellartec Pages: 35
Arctic King AKW+08CR4 Installation Instructions Manual preview
AKW+08CR4
Brand: Arctic King Pages: 30
AllerAir 5000W - Vocarb Features preview
5000W - Vocarb
Brand: AllerAir Pages: 2
ACSI FA2000EC Operating & Maintenance Manual preview
FA2000EC
Brand: ACSI Pages: 8
Dyson purehot+cool link Manual preview
purehot+cool link
Brand: Dyson Pages: 136
Gree G1707M Operating Instructions Manual preview
G1707M
Brand: Gree Pages: 24
A.O. Smith KJ1200F-B01-HK Instruction Manual preview
KJ1200F-B01-HK
Brand: A.O. Smith Pages: 16
Airwell /yaz218 Service Manual preview
/yaz218
Brand: Airwell Pages: 84
Heiko JS035-C1 Service Manual preview
JS035-C1
Brand: Heiko Pages: 52
Omega OTEC IEWB Series Service Manual preview
OTEC IEWB Series
Brand: Omega Pages: 18
Daikin VRV-WII FXYCP10MY1 Installation Procedure preview
VRV-WII FXYCP10MY1
Brand: Daikin Pages: 35

Brands by name

Popular brands

Load more brands