Mitsubishi Electric PUHY-(E)P300 Page 168 Service Handbook Download | Manualshive

Page: 168 / 302

background image

[

IX

Troubleshooting ]

- 159 -

HWE07010

GB

1. Error

Code

Abnormal discharge air temperature

2. Error

definition and error detection method

1) If the discharge temperature of 120 °C [248°F] or more is detected during the above operation (the first detection), the outdoor

unit stops once, turns to anti-restart mode for 3 minutes, and restarts after 3 minutes automatically.

2) If the discharge temperature of 120° C [248°F] or more is detected again (the second detection) within 30 minutes after the

second stop of the outdoor unit described above, the mode will be changed to 3 - minute restart mode, then the outdoor unit
will restart in 3 minutes.

3) If the discharge temperature of 120°C [248°F] or more is detected (the third detection) within 30 minutes after the stop of the

outdoor unit described above (regardless of the first or the second stop), the outdoor unit will make an error stop, and the error
code "1102" will be displayed.

4) If the discharge temperature of 120°C [248°F] or more is detected more than 30 minutes after the previous stop of the outdoor

unit, the detection is regarded as the first detection, and the operation described in step 1 above will start.

5) For 30 minutes after the stop (the first stop or the second stop) of the outdoor unit, preliminary errors will be displayed on the

LED display.

3. Cause, check method and remedy

1102

Cause

Check method and remedy

(1)

Gas leak, gas shortage

Refer to the page on refrigerant amount

evaluation.(page 109)

(2)

Overload operation

Check operating conditions and operation status of indoor/

outdoor units.

(3)

LEV failure on the indoor unit

Perform a cooling or heating operation to check the opera-

tion.

Cooling: Indoor unit LEV

LEV1

LEV2a,b

Heating: Indoor unit LEV

LEV2a,b

Refer to the section on troubleshooting the LEV.(page 226)

(4)

Outdoor unit LEV1 actuation failure

Outdoor unit LEV2a, b actuation failure

(5)

Closed ball valve

Confirm that the ball valve is fully open.

(6)

Outdoor fan (including fan parts) failure, mo-

tor failure, or fan controller malfunction

Rise in discharge temp. by low pressure

drawing for (3) - (6).

Check the fan on the outdoor unit.

Refer to the section on troubleshooting the outdoor unit

fan.(page 225)

(7)

Gas leak between low and high pressures

(4-way valve failure, Compressor failure, So-

lenoid valve (SV1a) failure)

Perform a cooling or heating operation and check the opera-

tion.

(8)

Thermistor failure

(TH4)

Check the thermistor resistor.(page 179)

(9)

Input circuit failure on the controller board

thermistor

Check the inlet air temperature on the LED monitor.

«
...
166
167
168
169
170
...
»

Summary of Contents for PUHY-(E)P300















































































































































































































































































































Reviews:

No comments

Related manuals for PUHY-(E)P300

Brand: WarmPool Pages: 18

Brand: GD Midea Refrigeration Equipment Pages: 30

Brand: Danby Pages: 34

Brand: Danby Pages: 40

Brand: U-Earth Biotech Pages: 16

Brand: Zamil Pages: 20

Brand: Daikin Pages: 84

Therapy Air Smart TAS-100

Brand: Zepter Pages: 9

Brand: Rheem Pages: 28

CS-25V1A-H1; CS-35V1A-E2; CS-50V9A-S; CS-70V9A-T

Brand: Chigo Pages: 66

Brand: Trane Pages: 24

Brand: Klarstein Pages: 132

ROOFTOP FLEXY FCA 100

Brand: Lennox Pages: 142

Brand: SPT Pages: 18

Brand: UV CAN SANITIZE Pages: 8

Brand: PremierOne Pages: 7

Brand: Bard Pages: 23

Brand: Carrier Pages: 92

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands