Mitsubishi Electric PUHY-(E)P300 Page 116 Service Handbook Download

Page: 116 / 302

[

VIII

Test Run Mode ]

- 107 -

HWE07010

VIII

Test Run Mode

[1] Items to be checked before a Test Run

(1) Check for refrigerant leak and loose cables and connectors.

(2) Measure the insulation resistance between the power supply terminal block and the ground with a 500V megger and

make sure it reads at least 1.0Mohm.

Do not operate the unit if the insulation resistance is below 1.0Mohm.

Do not apply megger voltage to the terminal block for transmission line. Doing so will damage the controller board.

The insulation resistance between the power supply terminal block and the ground could go down to close to 1Mohm imme-

diately after installation or when the power is kept off for an extended period of time because of the accumulation of refrigerant

in the compressor.

If insulation resistance reads at least 1Mohm, by turning on the main power and powering the crankcase heater for at least

12 hours, the refrigerant in the compressor will evaporate and the insulation resistance will go up.

Do not measure the insulation resistance of the terminal block for transmission line for the unit remote controller.

(3) Check that the valve on the gas pipe and liquid pipe are fully open.

Securely tighten the cap.

(4) Check the phase sequence and the voltage of the power supply.

(5) [When a transmission booster is connected]

Turn on the transmission booster before turning on the outdoor units.

If the outdoor units are turned on first, the connection information for the refrigerant circuit may not be properly recognized.

In case the outdoor units are turned on before the transmission booster is turned on, perform a power reset on the outdoor

units after turning on the power booster.

(6) Turn on the main power to the unit at least 12 hours before test run to power the crankcase heater.

Insufficient powering time may result in compressor damage.

(7) When a power supply unit is connected to the transmission line for centralized control, perform a test run with the

power supply unit being energized. Leave the power jumper connector on CN41 as it is (factory setting).

Summary of Contents for PUHY-(E)P300















































































































































































































































































































Search results

Summary of Contents for PUHY-(E)P300

Reviews:

Related manuals for PUHY-(E)P300

Brands by name

Popular brands

Mitsubishi Electric PUHY-(E)P300, Service Handbook

Search results

Summary of Contents for PUHY-(E)P300

Reviews:

Related manuals for PUHY-(E)P300

Brands by name

Popular brands