Mitsubishi Electric GT14, User Manual

Page: 1134 / 1546

49 - 26
49. CONNECTION TO YASKAWA PLC
49.3 Ethernet Connection
(2) Setting for the built-in MP2300S Ethernet and 218IF-02
Make the parameter settings with a peripheral tool.
*1 Set the same the Node IP Address (Remote Station's IP
Address) and the Node Port (Remote Station's Port Number)
as the Local IP Address and the Local Port (Local Station's
Port Number) on the GOT side.
For the Local IP Address and the Local Port (Local Station's
Port Number) on the GOT side, refer to the following.
49.3.2  Ethernet setting
(3) Setting of 218TXB
(a) DIP switch (SW2) setting
Set all the "unused" switches to off. When the
"unused" switches are on, the PLC does not
operate properly. In addition, when the PLC is
operated with the TEST switch on, the module
shifts to the self-check mode and communication is
disabled. To start communication, turn the TEST
switch to off.
(b) Parameter setting
Make the parameter settings with a peripheral tool.
*1 Set the same the Node IP Address (Remote Station's IP
Address) and the Node Port (Remote Station's Port Number)
as the Local IP Address and the Local Port (Local Station's
Port Number) on the GOT side.
For the Local IP Address and the Local Port (Local Station's
Port Number) on the GOT side, refer to the following.
49.3.2  Ethernet setting
Item Set value Range
Transmission
parameter
setting
IP Address [ ].[ ].[ ].[ ]
PLC side IP
address
Subnet Mask [ ].[ ].[ ].[ ]
PLC side setting
Gateway IP Address [ ].[ ].[ ].[ ]
Device name Arbitrary
Up to 16 one-byte
characters
Transmission
parameter
detailed
setting
Engineering Port 256 to 65535
For a connection
with software
MPE720
Response Time 0
Not required for
communication
with GOT
Count of Retry
(Number of Retries)
0
Message
communicati
on of
connection
parameter
setting
Connection Number 1
• Range of built in
MP2300S
Ethernet: 1 to 4
• Range of 218IF-
02: 1 to 20
Local Port 10500 256 to 65534
Node
IP Address
*1
[ ].[ ].[ ].[ ]
GOT side IP
address
Node Port
*1
[ ] GOT side port No.
Connection Type
UDP
(recommended)
UDP/TCP
Protocol Type
Extended
MEMOBUS
Extended
MEMOBUS,
MEMOBUS,
MELSEC,
None,
MODBUS/TCP
Code BIN RTU, BIN, ACII
Node Name (Remote
Station's Name)
Arbitrary
Up to 32 one-byte
characters (16 two-
byte characters)
SW2
N/O
10/100
F/H
INIT
TEST
ON OFF
Display Name
Stat
us
Operation Set value
N/O
Mode
selection
ON
Extended mode
(13 channels, Max. 1024 words)
ON
(Extended
mode)
OFF
Basic mode
(10 channels, Max. 512 words)
- Unused OFF
10/100
Transmis
sion
speed
ON 10Mbs
OFF
(100Mbps)
OFF 100Mbps
F/H
Transmis
sion
mode
ON Full duplex mode communication OFF
(Half duplex
mode)
OFF Half duplex mode communication
INIT
Initial
startup
ON
Startup with the default IP address
and the default engineering port No.
OFF
OFF
Startup with the IP address and the
engineering port No set in CP-717.
TEST TEST
ON Self check (Self check is conducted
when the module is started with the
TEST switch on.)
OFF
OFF
Item Set value Range
Transmission
parameter
setting
IP Address [ ].[ ].[ ].[ ]
PLC side IP
address
Subnet Mask [ ].[ ].[ ].[ ]
PLC side setting
Gateway IP Address [ ].[ ].[ ].[ ]
Device name Arbitrary
Up to 16 one-byte
characters
Transmission
parameter
detailed setting
Engineering Port 256 to 65535
For a connection
with software
MPE720
Response Time 0
Not required for
communication
with GOT
Count of Retry
(Number of Retries)
0
Message
communication
of connection
parameter
setting
Connection Number 1
• Range of built
in MP2300S
Ethernet: 1 to 4
• Range of
218IF-02: 1 to
20
Local Port 10500 256 to 65534
Node IP Address
*1
[ ].[ ].[ ].[ ]
GOT side IP
address
Message
communication
of connection
parameter
setting
Node Port
*1
[ ] GOT side port No.
Connection Type
UDP
(recommended)
UDP/TCP
Protocol Type
Extended
MEMOBUS
Extended
MEMOBUS,
MEMOBUS,
MELSEC, None,
MODBUS/TCP
Code BIN RTU, BIN, ACII
Node Name
(Remote Station's
Name)
Arbitrary
Up to 32 one-byte
characters (16
two-byte
characters)