Mitsubishi Electric 800 Series, Instruction Manual, Page: 113 / 727

Parameter List
Parameter list (by parameter number)
112
PARAMETERS
Mo
to
r c
ons
ta
nt
s
702 C106
Maximum motor frequency 0 to 400 Hz, 9999 0.01 Hz 9999 436
706 C130
Induced voltage constant (phi f)
0 to 5000 mV/(rad/s),
9999 0.1 mV/
(rad/s)
9999 436
707 C107
Motor inertia (integer) 10 to 999, 9999 1 9999 436
711 C131
Motor Ld decay ratio 0 to 100%, 9999 0.1% 9999 436
712 C132
Motor Lq decay ratio 0 to 100%, 9999 0.1% 9999 436
717 C182
Starting resistance tuning
compensation
0 to 200%, 9999 0.1% 9999 436
721 C185
Starting magnetic pole position
detection pulse width 0 to 6000 μ s, 10000 to
16000 μ s, 9999
1 μ s 9999 436
724 C108
Motor inertia (exponent) 0 to 7, 9999 1 9999 436
725 C133
Motor protection current level 100 to 500%, 9999 0.1% 9999 436
738 C230
Second motor induced voltage
constant (phi f) 0 to 5000 mV/(rad/s),
9999 0.1 mV/
(rad/s)
9999 436
739 C231
Second motor Ld decay ratio 0 to 100%, 9999 0.1% 9999 436
740 C232
Second motor Lq decay ratio 0 to 100%, 9999 0.1% 9999 436
741 C282
Second starting resistance tuning
compensation
0 to 200%, 9999 0.1% 9999 436
742 C285
Second motor magnetic pole
detection pulse width 0 to 6000 μ s, 10000 to
16000 μ s, 9999
1 μ s 9999 436
743 C206
Second motor maximum frequency 0 to 400 Hz, 9999 0.01 Hz 9999 436
744 C207
Second motor inertia (integer) 10 to 999, 9999 1 9999 436
745 C208
Second motor inertia (exponent) 0 to 7, 9999 1 9999 436
746 C233
Second motor protection current
level
100 to 500%, 9999 0.1% 9999 436
PI
D
co
nt
ro
l
753 A650
Second PID action selection
0, 10, 11, 20, 21, 50, 51,
60, 61, 70, 71, 80, 81,
90, 91, 100, 101, 1000,
1001, 1010, 1011, 2000,
2001, 2010, 2011
1 0 488
754 A652
Second PID control automatic
switchover frequency
0 to 590 Hz, 9999 0.01 Hz 9999 488
755 A651
Second PID action set point 0 to 100%, 9999 0.01% 9999 488
756 A653
Second PID proportional band 0.1 to 1000%, 9999 0.1% 100% 488
757 A654
Second PID integral time 0.1 to 3600 s, 9999 0.1 s 1 s 488
758 A655
Second PID differential time 0.01 to 10 s, 9999 0.01 s 9999 488
759 A600
PID unit selection 0 to 43, 9999 1 9999 501
PI
D pr
e-
char
g
e
fu
nc
ti
on
760 A616
Pre-charge fault selection 0, 1 1 0 504
761 A617
Pre-charge ending level 0 to 100%, 9999 0.1% 9999 504
762 A618
Pre-charge ending time 0 to 3600 s, 9999 0.1 s 9999 504
763 A619
Pre-charge upper detection level 0 to 100%, 9999 0.1% 9999 504
764 A620
Pre-charge time limit 0 to 3600 s, 9999 0.1 s 9999 504
765 A656
Second pre-charge fault selection 0, 1 1 0 504
766 A657
Second pre-charge ending level 0 to 100%, 9999 0.1% 9999 504
767 A658
Second pre-charge ending time 0 to 3600 s, 9999 0.1 s 9999 504
768 A659
Second pre-charge upper detection
level
0 to 100%, 9999 0.1% 9999 504
769 A660
Second pre-charge time limit 0 to 3600 s, 9999 0.1 s 9999 504
Moni
tor
fu
nctio
n
774 M101
Operation panel monitor selection 1
1 to 3, 5 to 14,
17 to 20, 22 to 36, 38,
40 to 46, 50 to 57, 61,
62, 64, 67, 71 to 75,
87 to 98, 100, 9999
1 9999 347
775 M102
Operation panel monitor selection 2 1 9999 347
776 M103
Operation panel monitor selection 3 1 9999 347
─ 777
A681
4 mA input fault operation
frequency
0 to 590 Hz, 9999 0.01 Hz 9999 411
T053
─ 778
A682
4 mA input check filter 0 to 10 s 0.01 s 0 s 411
T054
─
779 N014
Operation frequency during
communication error
0 to 590 Hz, 9999 0.01 Hz 9999 546
─ 791 F070
Acceleration time in low-speed
range
0 to 3600 s, 9999 0.1 s 9999 269
Functio
n
Pr.
Pr.
group
Name Setting range
Minimum
setting
increments
Initial value
Refer
to
page
Customer
settin
g