Minolta Di620, Manual, Page: 290 / 466

T-75
21) C10
∗∗
~C14
∗∗
•
These malfunctions are concerned with faulty symptoms as they relate to software, hardware, and
communications. For remedial action change the board, check for cable connections, and turn OFF
and ON the power.
Code Action
C10
∗∗
C11
∗∗
C12
∗∗
➀
Reset the malfunction and turn OFF and ON the Power Switch.
➁
If the same malfunction is still detected, check cables for proper connection and, if
they are okay, change PWB-B.
C12C
∗
➀
Run "Hard Disk Format" of "Image Memory" under "Function" available from the
Tech. Rep. mode.
➁
If the same malfunction is still detected, change the Hard Disk Drive.
➂
If the malfunction is again detected, change PWB-B.
C1300
➀
Reset the malfunction and turn OFF and ON the Power Switch.
➁
If the same malfunction is still detected, check the polygon driver, PWB-A, and con-
nector and, if they are okay, change either the polygon driver, PH Unit, or PWB-A.
C1326
➀
Reset the malfunction and turn OFF and ON the Power Switch.
➁
If the same malfunction is still detected, check PWB-B MJ1 for proper connection
and, if it is okay, change either PWB-B or PWB-A.
C1330
C1334
➀
Reset the malfunction, turn OFF and ON the Power Switch, and unplug the power
cord and plug it in again.
➁
If the malfunction is still detected, change PWB-A.
➂
If the malfunction is again detected, run "I.R. Mem. Prn" of "Image Memory"
under "Function" available from the Tech. Rep. mode. If "NG" is shown, check the
harness between PWB-A, PWB-B, and PWB-IB and, if the harness is intact, change
the board.
C133B Check cables for proper connection and, if they are okay, change the Finisher CPU
board.
C13F0
C13F1
➀
Reset the malfunction and turn OFF and ON the Power Switch.
➁
If the same malfunction is still detected, check the PWB-J connector and, if it is okay,
change either the PH Unit, PWB-J, or PWB-A.
C13F2
C13F3 Check the Trailing Edge Stop and Edge Guide mechanism and harness and, if they are
okay, change PWB-A or PWB-F.
C13F4
➀
Reset the malfunction.
➁
If the same malfunction is still detected, select "Adjust"
→
"Printer"
→
"Registration
(CD)" and make settings so that their total becomes less than 10.
➂
If the same malfunction is still detected, replace the PH Unit.
C1401
➀
Reset the malfunction (i.e., turn OFF and ON the Power Switch).
➁
If the same malfunction is still detected, change PWB-IB.
C1402
➀
Reset the malfunction (i.e., turn OFF and ON the Power Switch).
➁
If the same malfunction is still detected, change PWB-IB.
C1410
➀
Reset the malfunction (i.e., turn OFF and ON the Power Switch).
➁
If the same malfunction is still detected, change PWB-IB.
C1426
➀
Reset the malfunction.
➁
If the same malfunction is still detected, change PWB-IB.
C1428
➀
Reset the malfunction.
➁
If the same malfunction is still detected, change PWB-IB.
C1429
➀
Reset the malfunction.
➁
If the same malfunction is still detected, change PWB-B.
➂
If the malfunction is again detected, change PWB-IB.
C142A
➀
Reset the malfunction.
➁
If the same malfunction is still detected, change PWB-IB.
C1430
➀
Reset the malfunction (i.e., turn OFF and ON the Power Switch).
➁
If the same malfunction is still detected, change PWB-IB.
C143E
∗
See the relevant option service manual.
→
←
→
←