MIMAKI CG-100SRIII Operation Manual Download

Page: 16 / 172

1-4

The Rear

Clamp pressure lever

This lever adjusts the force by
which the clamp is held.
(

P.1-8)

Tray

Small tools, such as a retractable knife and
other cutters, can be placed on.

Roll bar

A roll sheet is placed on the two roll
bars. (

P.2-19)

AC inlet

The power cable is
connected to the AC
inlet.(

P.1-10)

Sheet sensor

This sensor detects the presence of
the sheet and sheet length. (

P.1-

Roll stay

Roll stays support the roll
bars.
(

P.2-19)

RS-232C interface connector

The RS-232C interface
connector. (

P.1-9)

LAN connector

The LAN connector.
Please use when you use
event mail function.

USB interface connector

The USB interface connector.
(

P.1-9)

Summary of Contents for CG-100SRIII













































































































































































Search results

Summary of Contents for CG-100SRIII

Reviews:

Related manuals for CG-100SRIII

Brands by name

Popular brands

MIMAKI CG-100SRIII, Operation Manual

Search results

Summary of Contents for CG-100SRIII

Reviews:

Related manuals for CG-100SRIII

Brands by name

Popular brands