MIMAKI CG-100SRIII Page 149 Operation Manual Download

Page: 149 / 172

Cutter blade

5-5

Appendix

Replacing the cutter other than supplied one

Loosen the lock nut, and pull the adjusting knob
out of the holder.

Insert the cutter into the adjusting knob using
tweezers.

Tighten the lock nut.

Adjusting blade edge of cutter other than supplied one

After the completion of adjustment, be sure to set cutting conditions and perform test cutting to check the
cutting quality.

Remove the cutter holder, and loosen the lock nut.

」

Turn the adjusting knob to adjust the protruding
amount of the cutter blade.

Tighten the lock nut so that the adjusting knob will
not turn.

• The blade adjuster (adjuster: OPT-S1005) will facilitate the adjustment of the protruding amount of the

blade.

Lock nut

Adjusting knob

Lock nut

Adjusting knob

Summary of Contents for CG-100SRIII













































































































































































Search results

Summary of Contents for CG-100SRIII

Reviews:

Related manuals for CG-100SRIII

Brands by name

Popular brands

MIMAKI CG-100SRIII, Operation Manual

Search results

Summary of Contents for CG-100SRIII

Reviews:

Related manuals for CG-100SRIII

Brands by name

Popular brands