MerCruiser Axius 350 Instruction Manual Download Page 69 | Manualshive

Page: 69 / 149

background image

Section 3 - On The Water

90-8M0053363

eng

NOVEMBER 2010

Page 61

33824

Label in the vicinity of the transom boarding area

IMPORTANT: If either of the labels cannot be located or are not legible, they must be replaced before engaging Skyhook. Contact

the manufacturer of your boat, your Cummins distributor, or an Authorized Cummins MerCruiser Diesel Repair Facility and replace

the labels.

NOTE: Skyhook will not engage while "DOCK" mode is engaged. Disengage "DOCK" mode prior to engaging "SKYHOOK."

1. Bring the boat to a stop and move the ERC levers to neutral. Skyhook will not engage until the boat is in neutral.
2. Inform passengers to stay out of the water and off the swim platform, and to be alert for any sudden shifts in the boats position

when skyhook is engaged.

3. Ensure that no one is on the swim platform, or in the water anywhere near the boat.

!

WARNING

A rotating propeller, a moving boat, or a device attached to a moving boat can cause serious injury or death to people in the

water. When Skyhook is engaged, the propellers rotate and the boat moves to maintain the position of the boat. Stop the engines

immediately whenever anyone is in the water near the boat.

4. Press the "SKYHOOK" button to engage Skyhook.

a -

Indicator light

b -

"SKYHOOK" button

35570

a

b

«
...
67
68
69
70
71
...
»

Summary of Contents for Axius 350






















































































































































Reviews:

No comments

Related manuals for Axius 350

Brand: Tecumseh Pages: 94

Brand: Leb Electronics Pages: 24

Brand: Pacific Pages: 48

Brand: Nouvag Pages: 8

EASY-KART 100cc

Brand: IAME Pages: 35

MotorLift RA20F

Brand: Chamberlain Pages: 24

Brand: Chamberlain Pages: 40

Brand: YS Pages: 5

Brand: SPE Pages: 7

Brand: TEM Pages: 19

75-200 V DC Series

Brand: TEM Pages: 38

Brand: TEM Pages: 42

Brand: YS Pages: 2

Brand: HIOTH TECHNOLOGY Pages: 5

Brand: Honda Pages: 5

Brand: Honda Pages: 60

Brand: Teknic Pages: 30

Brand: Hotsy Pages: 68

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands