MerCruiser Axius 350 Instruction Manual Download Page 60

Page: 60 / 149

Section 3 - On The Water

Page 52

90-8M0053363

eng

NOVEMBER 2010

•

Press one of the "TURN" buttons in the direction you want to turn. Each press of the button changes the desired heading

by 10°.

a -

Port "TURN" button

b -

Starboard "TURN" button

•

Tap the joystick in the direction you want to turn. Tapping the joystick left (port) or right (starboard) adjusts your course

by 1° for each movement.

24707

Adjusting the heading to starboard (port opposite)

6. Turn the wheel or press the "AUTO HEADING" button to disengage Auto Heading and a single beep sounds. If the steering

wheel is used to disengage Auto Heading, the resume button LED turns on and a single beep sounds. While the LED is lit,

you can press the "RESUME" button to resume auto heading.

a -

Port "TURN" button

b -

Starboard "TURN" button

c -

"AUTO HEADING" button

d -

"RESUME" button

RESUME

STANDBY

ACTIVE

AUTO

HEADING

TURN

32508

RESUME

STANDBY

ACTIVE

AUTO

HEADING

TURN

32509

Summary of Contents for Axius 350






















































































































































Search results

Summary of Contents for Axius 350

Reviews:

Related manuals for Axius 350

Brands by name

Popular brands

MerCruiser Axius 350, Instruction Manual

Search results

Summary of Contents for Axius 350

Reviews:

Related manuals for Axius 350

Brands by name

Popular brands