MerCruiser Axius 350 Instruction Manual Download Page 99

Page: 99 / 149

Section 5 - Maintenance

90-8M0053363

eng

NOVEMBER 2010

Page 91

Tube Ref No.

Description

Where Used

Part No.

High Performance Gear

Lubricant

Gear lube monitor

92-858064K01

3. Ensure that the rubber gasket is inside the cap and install the cap. Do not overtighten.

NOTE: When filling the entire sterndrive unit refer to Changing.

Changing

1. Remove the gear lube monitor from the bracket.

a -

Gear lube monitor

b -

Typical closed cooled

model

c -

Typical seawater cooled

model

2. Empty the contents into a suitable container.
3. Install the gear lube monitor in the bracket.
4. Place the sterndrive unit in full trim limit out position, remove the fill and drain screw and sealing washer and drain the gear

lube.

a -

Fill and drain screw

b -

Sealing washer

5. Remove the vent screw and sealing washer. Allow the gear lube to drain completely.

a -

Vent screw

b -

Sealing washer

IMPORTANT: If any water drained from the gear lube fill and drain hole, or if the gear lube appears milky, the sterndrive unit

is leaking and should be checked immediately by your authorized Mercury MerCruiser dealer.

6. Lower the sterndrive unit so that the propeller shaft is level. Fill the sterndrive unit, through the fill and drain hole, with specified

gear lubricant until an air‑free stream of lubricant flows from the vent hole.

32539

mc79507-1

mc77106-1

Summary of Contents for Axius 350






















































































































































Search results

Summary of Contents for Axius 350

Reviews:

Related manuals for Axius 350

Brands by name

Popular brands

MerCruiser Axius 350, Instruction Manual

Search results

Summary of Contents for Axius 350

Reviews:

Related manuals for Axius 350

Brands by name

Popular brands