MerCruiser Axius 350 Instruction Manual Download Page 63

Page: 63 / 149

Section 3 - On The Water

90-8M0053363

eng

NOVEMBER 2010

Page 55

The "ACTIVE" light is illuminated when one mode of Axius is on.

a -

"STANDBY" light

b -

"ACTIVE" light

Power Icon

The power icon

indicates a button that engages or disengages an Axius Premier touchad function indicated on the button.

Only one function can be on at a time.

If you press a button that has the power icon

when that button light is on, the light turns off for that button and the "STANDBY"

light illuminates.

If you press a button with the power icon

when that button light is off, the light turns on for that button, a single beep sounds,

and the "ACTIVE" light illuminates.

Buttons with power icons

a -

"SKYHOOK" button

b -

"AUTO HEADING" button

c -

"TRACK WAYPOINT" button

Auto Heading

1. At least one engine must be running for auto heading to function.

35564

35563

Summary of Contents for Axius 350






















































































































































Search results

Summary of Contents for Axius 350

Reviews:

Related manuals for Axius 350

Brands by name

Popular brands

MerCruiser Axius 350, Instruction Manual

Search results

Summary of Contents for Axius 350

Reviews:

Related manuals for Axius 350

Brands by name

Popular brands