MerCruiser Axius 350 Instruction Manual Download Page 88

Page: 88 / 149

Section 4 - Specifications

Page 80

90-8M0053363

eng

NOVEMBER 2010

Engine

IMPORTANT: It may be necessary to adjust oil levels depending on installation angle and cooling systems (heat exchanger and

fluid lines).
Always use the dipstick to determine the exact quantity of oil or fluid required.

All Models

Capacity

Fluid Type

Engine oil (with filter)

4.25 liters

(4.5 U.S. qt.)

Mercury/Quicksilver Synthetic Blend MerCruiser Engine Oil

25W‑40

Seawater cooling system

(winterization use only)

20 liters (21 U.S. qt.)

Propylene Glycol and Purified Water

Closed cooling system

19 liters (20 U.S. qt.)

Mercury Extended Life Coolant/Antifreeze or Extended Life

Ethylene Glycol 5/100 Coolant/Antifreeze mixed 50/50 with

Purified Water

Sterndrive—Bravo

NOTE: Oil capacity includes gear lube monitor.

Model

Capacity

Fluid Type

Bravo Three with dual water pickups

2736 mL (92‑1/2 oz)

High Performance Gear Lubricant

Bravo Three with side water pickups only

2972 mL (100‑1/2 oz)

Steering

Axius—All Models

Capacity

Fluid Type

Steering system

2914 mL (98‑1/2 oz)

Dexron III

Power Trim

Description

Part Number

Power Trim and Steering Fluid

92‑858074K01

SAE Engine Oil 10W‑30

Obtain locally

SAE Engine Oil 10W‑40

Summary of Contents for Axius 350






















































































































































Search results

Summary of Contents for Axius 350

Reviews:

Related manuals for Axius 350

Brands by name

Popular brands

MerCruiser Axius 350, Instruction Manual

Search results

Summary of Contents for Axius 350

Reviews:

Related manuals for Axius 350

Brands by name

Popular brands