background image

Section 3 - On The Water

90-8M0053363   

eng

  NOVEMBER  2010

Page  67

Response Button

1. Press the "RESPONSE" button to change the how hard the selected Axius Premier program tries to keep the boat in position

in the various modes.

a -

Indicator lamp

b -

"RESPONSE" button

2. Press the "RESPONSE" button again to change the gain further. Each time you press the "RESPONSE" button, the button

light blinks to indicate the gain setting for that mode. The initial button press shows the current setting value. Additional button

presses increase the gain in steps up to three and then return to one.

Number of blinks

Response setting indicated

Aggressiveness of correction

1

1

Mild (for gentle or calm conditions)

2

2

Medium (for moderate conditions)

3

3

Aggressive (for severe conditions)

3. The response level indication will appear on the Auto Heading page in VesselView.

Track Waypoint

!

 WARNING

In some Precision Pilot modes—"Auto Heading," "Track Waypoint," and "Waypoint Sequence"—the boat navigates a preset

course. The boat does not automatically respond to hazards such as other watercraft, obstacles, swimmers, or underwater

terrain. Collision with these hazards could cause boat damage, serious injury, or death. The operator must stay at the helm,

ready to evade hazards and warn others of course changes.

IMPORTANT: Track Waypoint can only be used with chart plotters approved by CMD.
Track Waypoint allows the boat to automatically navigate to a specific waypoint or sequence of waypoints, called a waypoint route.

Waypoint data needs to be provided to VesselView by a third party chart plotter. Refer to your chart plotter's user manual for

details.

Engaging Track Waypoint Mode

To engage the Track Waypoint mode of Axius Premier:
1. Turn on the chart plotter and select a single waypoint or waypoint route to be tracked.
2. Place at least one ERC handle in forward gear. Track Waypoint does not function if both handles are in neutral or reverse.
3. Manually steer the boat to the direction of the first waypoint and hold the boat steady at a safe operating speed.

35571

a

b

Summary of Contents for Axius 350






















































































































































Reviews: