MerCruiser Axius 350 Instruction Manual Download Page 58

Page: 58 / 149

Section 3 - On The Water

Page 50

90-8M0053363

eng

NOVEMBER 2010

To disengage Sync mode:
1. Place the ERC levers in any detent.
2. Press the "SYNC" button.
To re‑engage Sync mode, press the "SYNC" button.

Axius Plus CAN Control Pad (If Equipped)

General Information

•

Axius Plus CAN Control Pad functions are controlled through the Axius trackpad only.

•

Axius Plus CAN Control Pad screens, when accessed by the trackpad, appear on the VesselView for three seconds unless

calibrated otherwise.

•

Pressing any button on VesselView dismisses the Axius Plus CAN Control Pad screen from the VesselView screen, unless

the screen was chosen from the VesselView environment menu.

NOTE: Not all of the functions of the Axius system work when DTS functions are engaged. Disengage the DTS functions to use

the functions of Axius track pad.

The following information shows the location and explains the function of the Axius track pad lights and buttons.

Heading Adjustment and Override

When Auto Heading is engaged, the steering wheel feels locked into a detent . Approximately 3.4–4.5 kg (8–10 lb.) of force are

required to overcome this detent. Manually overcoming the steering wheel's detent force automatically puts Axius CAN into standby

mode.
1. When Auto Heading is engaged the "TURN" buttons provide a 10° course correction for each press to the port or starboard.
2. The joystick provides a 1° course correction for each press to the port or starboard.

Standby

•

In standby mode, the display shows a digital compass value and the angle of the drives when engaged.

•

The compass value is the actual current heading from the Axius CAN.

•

On the right side of the screen, an icon labeled "OFF" indicates that the Axius track pad is not engaged.

Standby and Active Lights

Axius Plus CAN Control Pad is disengaged (off) when the "STANDBY" light is illuminated. You must press a button to engage a

mode.
When the "ACTIVE" light is illuminated one mode of Axius is engaged (on).

a -

"STANDBY" light

b -

"ACTIVE" light

Power Icon

The power icon

indicates a button that engages or disengages an Axius Plus CAN Control Pad function indicated on the

button.

If you press a button that has the power icon

when that button light is on, the light turns off for that button and the "STANDBY"

light illuminates.

RESUME

STANDBY

ACTIVE

AUTO

HEADING

TURN

32506

Summary of Contents for Axius 350






















































































































































Search results

Summary of Contents for Axius 350

Reviews:

Related manuals for Axius 350

Brands by name

Popular brands

MerCruiser Axius 350, Instruction Manual

Search results

Summary of Contents for Axius 350

Reviews:

Related manuals for Axius 350

Brands by name

Popular brands