MerCruiser Axius 350 Instruction Manual Download Page 149

Page: 149 / 149

Section 8 - Customer Assistance Information

90-8M0053363

eng

NOVEMBER 2010

Page 141

Safety

Customer

Dealer

Enable Throttle Only and demonstrate its ability to disable shifting of the electronic remote control

and joystick while engines are running.

☐

Joystick

Customer

Dealer

Demonstrate that the joystick requires both engines to be running to operate.

☐

Rotate the joystick to port and starboard to demonstrate pivot capabilities.

☐

Place the joystick to port to translate the boat while demonstrating the ability to compensate for

current and wind by rotating the top of the joystick and inputting slight forward and reverse inputs.

Repeat going starboard.

☐

Enable docking mode to demonstrate reduced throttle response for joystick maneuvers.

☐

Upgrades

Customer

Dealer

Demonstrate methods to enable and disable Auto Heading, if equipped.

☐

Demonstrate methods to enable and disable Skyhook, if equipped.

☐

Demonstrate methods to enable and disable AutoPilot Waypoint Sequencing, if equipped.

☐

Steering wheel

Customer

Dealer

Demonstrate that the starboard keyswitch is required to be on for steering wheel autocenter and

force feedback.

☐

Inform the consumer where the 20 A circuit breaker is located.

☐

Demonstrate the steering wheel autocenter ability and conditions.

☐

Maintenance

Customer

Dealer

Inform the consumer about hydraulic power steering fluid level checks and service intervals.

☐

Summary of Contents for Axius 350






















































































































































Search results

Summary of Contents for Axius 350

Reviews:

Related manuals for Axius 350

Brands by name

Popular brands

MerCruiser Axius 350, Instruction Manual

Search results

Summary of Contents for Axius 350

Reviews:

Related manuals for Axius 350

Brands by name

Popular brands