MerCruiser Axius 350 Instruction Manual Download Page 77

Page: 77 / 149

Section 3 - On The Water

90-8M0053363

eng

NOVEMBER 2010

Page 69

2. You can resume the Track Waypoint heading within one minute, if the vessel has not turned too far and the "RESUME" light

is still on or flashing.

Turn Buttons or Joystick in Track Waypoint Mode

While in "TRACK WAYPOINT" mode, press the left or right "TURN" buttons on the Trackpad or use the joystick to change the

mode to "AUTO HEADING."

Auto Heading Button in Track Waypoint Mode

While in "TRACK WAYPOINT" mode, press the "AUTO HEADING" button to cause Axius Premier to change to "AUTO HEADING"

mode.

Acknowledging a Turn During a Waypoint Arrival

IMPORTANT: Track Waypoint mode does not automatically turn the boat upon arrival at a plotted waypoint.
1. When the boat enters a waypoint arrival zone as indicated by the chart plotter, a short horn beep sounds and the "WAYPOINT

SEQUENCING" button light starts blinking to inform the operator to make a turn.

a -

Indicator light

b -

"WAYPOINT SEQUENCE" button

2. If the Waypoint Sequence mode has not been engaged, the "WAYPOINT SEQUENCE" icon light blinks at the arrival zone.

31411

Waypoint Sequence icon light

35575

Summary of Contents for Axius 350






















































































































































Search results

Summary of Contents for Axius 350

Reviews:

Related manuals for Axius 350

Brands by name

Popular brands

MerCruiser Axius 350, Instruction Manual

Search results

Summary of Contents for Axius 350

Reviews:

Related manuals for Axius 350

Brands by name

Popular brands