MerCruiser Axius 350 Instruction Manual Download Page 78 | Manualshive

Page: 78 / 149

background image

Section 3 - On The Water

Page 70

90-8M0053363

eng

NOVEMBER 2010

3. VesselView displays a pop‑up screen warning. The operator must determine it is safe to turn the boat. If so, press the

"WAYPOINT SEQUENCE" button to acknowledge that it is safe for Axius Premier CAN Trackpad to automatically turn the

boat and maneuver to the new course.

31414

Pop-up screen warning

4. If the waypoint is not acknowledged, the boat continues on its current heading.
5. At the end of the Track Waypoint course, input a new route or take control of the boat. Otherwise, the boat will revert to auto

heading mode and continues on its last course heading.

Waypoint Sequence

1. Place the ERC lever or levers into forward. "WAYPOINT SEQUENCE" does not engage if the levers are in neutral or reverse.
2. If the Track Waypoint button light is not on, press the "TRACK WAYPOINT" button.
3. Press the "WAYPOINT SEQUENCE" button to engage Waypoint Sequence mode. The indicator light on the button will

illuminate.

a -

Indicator lamp

b -

"WAYPOINT SEQUENCE" button

35575

a

b

«
...
76
77
78
79
80
...
»

Summary of Contents for Axius 350






















































































































































Reviews:

No comments

Related manuals for Axius 350

Brand: Eaton Pages: 24

Brand: 3W Pages: 20

Brand: Selve Pages: 24

Brand: Ebmpapst Pages: 18

Brand: ebm-papst Pages: 11

Brand: Bison Pages: 19

Brand: cemp Pages: 18

Brand: Robin America Pages: 23

Brand: MULTIPLEX modell Pages: 11

Brand: Honda Pages: 50

Brand: Pratt & Whitney Pages: 576

Brand: O.S. engine Pages: 4

BREVINI V Series

Brand: DANA Pages: 34

Brand: Agrimate Pages: 32

Brand: DLE Pages: 4

Brand: Yanmar Pages: 20

Brand: Yanmar Pages: 50

Brand: Yanmar Pages: 50

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands