MerCruiser Axius 350 Instruction Manual Download Page 59

Page: 59 / 149

Section 3 - On The Water

90-8M0053363

eng

NOVEMBER 2010

Page 51

If you press a button with the power icon

when that button light is off, the light turns on for that button, a single beep sounds,

and the "ACTIVE" light illuminates.

Button with power icon

a -

"AUTO HEADING" button

b -

Power icon

Auto Heading

1. At least one engine must be running for auto heading to function.
2. Press the "AUTO HEADING" button to engage Axius. The button illuminates and a single beep sounds. A double beep sounds

if auto heading does not engage.

a -

"AUTO HEADING" button

b -

Power icon

3. Axius holds the compass heading the boat is following when the "AUTO HEADING" button is pressed.

31409

4. To make adjustments in the default heading while auto heading is active and the button light is on, press the respective

"TURN" button on the trackpad or tap (quickly move) the joystick.

5. To make a turn:

RESUME

STANDBY

ACTIVE

AUTO

HEADING

TURN

32507

RESUME

STANDBY

ACTIVE

AUTO

HEADING

TURN

32507

Summary of Contents for Axius 350






















































































































































Search results

Summary of Contents for Axius 350

Reviews:

Related manuals for Axius 350

Brands by name

Popular brands

MerCruiser Axius 350, Instruction Manual

Search results

Summary of Contents for Axius 350

Reviews:

Related manuals for Axius 350

Brands by name

Popular brands