MerCruiser Axius 350 Instruction Manual Download Page 72

Page: 72 / 149

Section 3 - On The Water

Page 64

90-8M0053363

eng

NOVEMBER 2010

31409

9. To adjust your course while "AUTO HEADING" is engaged, see

Course Adjustment Using the Turn Buttons or Joystick.

10. To disengage Auto Heading refer to

Disengaging Auto Heading

11. Press the "AUTO HEADING" button a second time, Auto Heading goes to Standby mode and all lights other than "STANDBY"

turn off.

Course Adjustment Using the Turn Buttons or Joystick

While in "AUTO HEADING" mode, the "TURN" buttons (course adjust buttons) change the set course heading each time they are

pressed. Tapping the joystick left or right adjusts your course for each tap.
1. Press the "TURN" button in the direction of the desired heading change. Each press of the button changes the desired heading

by 10°.

a -

Port "TURN" button

b -

Starboard "TURN" button

2. Move (press) the joystick in the desired direction to make small adjustments in the chosen heading. Each recognized

movement adjusts the chosen heading by 1°.

35567

Summary of Contents for Axius 350






















































































































































Search results

Summary of Contents for Axius 350

Reviews:

Related manuals for Axius 350

Brands by name

Popular brands

MerCruiser Axius 350, Instruction Manual

Search results

Summary of Contents for Axius 350

Reviews:

Related manuals for Axius 350

Brands by name

Popular brands