MerCruiser Axius 350 Instruction Manual Download Page 107 | Manualshive

Page: 107 / 149

background image

Section 5 - Maintenance

90-8M0053363

eng

NOVEMBER 2010

Page 99

NOTE: If the boat is operated at idle for prolonged periods of time, coupler should be lubricated every 50 hours

Bravo drive coupler

a -

Grease fitting

Tube Ref No.

Description

Where Used

Part No.

91

Engine Coupler Spline

Grease

Coupler

92-802869A 1

NOTE:

On Bravo models,

the coupler and shaft splines can be lubricated without removing the sterndrive. Apply lubricant from

a typical hand‑operated grease gun until a small amount of grease begins to push out.

Propellers

Propeller Repair

Some damaged propellers can be repaired. Contact your authorized Mercury MerCruiser dealer.

Bravo Three Propeller Removal

!

WARNING

Rotating propellers can cause serious injury or death. Never operate the boat out of the water with a propeller installed. Before

installing or removing a propeller, place the drive unit in neutral and engage the lanyard stop switch to prevent the engine from

starting. Place a block of wood between the propeller blade and the anti‑ventilation plate.

1. Place wood block between propeller blades and anti‑ventilation plate to prevent rotation.
2. Remove the bolt and washers securing the propeller shaft anode.
3. Remove the propeller shaft anode.

a -

Propeller

b -

Propeller shaft nut

c -

Propeller shaft anode

d -

Propeller shaft anode screw

e -

Flat washer

f -

Star washer

4. Turn aft propeller shaft nut 37 mm (1‑7/16 in.) counterclockwise to remove nut.
5. Slide propeller and thrust hub off propeller shaft.
6. Turn front propeller shaft nut 70 mm (2‑3/4 in.) counterclockwise to remove nut.
7. Slide propeller and thrust hub off propeller shaft.

a

a

14535

a

b

d

c

f

e

5303

«
...
105
106
107
108
109
...
»

Summary of Contents for Axius 350






















































































































































Reviews:

No comments

Related manuals for Axius 350

Brand: EuroLite Pages: 19

Brand: YOODA Pages: 6

Brand: Flux Pages: 28

Brand: Yanmar Pages: 100

Brand: Jiecang Pages: 2

2-10-4 TEXAS STEAM ENGINE

Brand: Premier Pages: 24

Brand: JetCat Pages: 54

Brand: Nakanishi Pages: 2

Brand: Yanmar Pages: 35

Brand: Detroit Diesel Pages: 174

Brand: WilTec Pages: 16

Brand: Ingersoll-Rand Pages: 42

Brand: EMAK Pages: 40

Brand: Melec Pages: 42

Brand: Mitsubishi Pages: 20

Brand: Ford Pages: 91

125 JUNIOR MAX evo

Brand: Rotax Pages: 54

Brand: YASKAWA Pages: 616

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands