MerCruiser Axius 350 Instruction Manual Download Page 66

Page: 66 / 149

Section 3 - On The Water

Page 58

90-8M0053363

eng

NOVEMBER 2010

6. To disengage auto heading, turn the steering wheel or press the "AUTO HEADING" button. A single beep sounds when it

disengages. If the steering wheel is used to disengage auto heading, the "RESUME" button LED turns on and a single beep

sounds. While the LED is lit, you can press the "RESUME" button to resume auto heading.

a -

Port "TURN" button

b -

Starboard "TURN" button

c -

"RESUME" button

d -

"AUTO HEADING" button

7. If the ERC handles are moved to neutral, Auto Heading turns off, a single beep sounds, and the "STANDBY" light turns on.

You cannot resume your course by pressing the "RESUME" button.

a -

"OFF" button

b -

Current heading

c -

Drive positions

d -

Engine RPM

Pressing the "AUTO HEADING" button causes VesselView to displays the "AUTO HEADING" screen for three seconds. If the

VesselView "AUTO HEADING" screen does not appear, the "AUTO HEADING" screen needs to be activated in VesselView

calibration. Axius still engages whether the screen appears or not.

NOTE: If you press the "AUTO HEADING" button a second time, the Axius goes to standby mode and all lights other than

"STANDBY" turn off.

Disengage Auto Heading

1. Disengage the "AUTO HEADING" mode by any of the following actions:

•

Place the ERC levers for both engines in neutral.

•

Turn the steering wheel beyond the detent.

35568

31408

Summary of Contents for Axius 350






















































































































































Search results

Summary of Contents for Axius 350

Reviews:

Related manuals for Axius 350

Brands by name

Popular brands

MerCruiser Axius 350, Instruction Manual

Search results

Summary of Contents for Axius 350

Reviews:

Related manuals for Axius 350

Brands by name

Popular brands