MerCruiser Axius 350 Instruction Manual Download Page 76

Page: 76 / 149

Section 3 - On The Water

Page 68

90-8M0053363

eng

NOVEMBER 2010

4. Press the "TRACK WAYPOINT" button on the Axius Premier Trackpad. The "TRACK WAYPOINT" button light turns on and

a single horn beep sounds, indicating Track Waypoint engaged. Track Waypoint tracks to the first waypoint on the chart plotter

course. Two horn beeps sound if Track Waypoint does not engage.

a -

Indicator lamp

b -

"TRACK WAYPOINT" button

5. The VesselView "TRACK WAYPOINT" screen displays on VesselView for one second after pressing the "TRACK

WAYPOINT" button. The display shows the digital heading that the boat is traveling, the angles of the drives, and engine

speed in RPM. See

Mode Display

VesselView

NOTE: This display screen is activated during VesselView calibration. The GPS system generates the displayed heading

based on magnetic North.

31413

Track Waypoint screen

Disengaging Track Waypoint Mode

1. Disengage the Track Waypoint mode by one of the following methods:

•

Press the "TRACK WAYPOINT" button on the Axius Premier Trackpad. The "TRACK WAYPOINT" button light goes off

and Axius Premier goes to Standby. The "STANDBY" light turns on

•

Turn the steering wheel hard enough to overcome the detent and Axius Premier features go into Standby.

•

Move both ERC levers back to neutral and Axius Premier goes to Standby.

•

Press either "TURN" button and Axius Premier goes to Auto Heading mode.

•

Press the "AUTO HEADING" button and Axius Premier CAN Trackpad goes to Auto Heading mode.

•

Turn off the chart plotter and Axius Premier goes to Standby.

35572

Summary of Contents for Axius 350






















































































































































Search results

Summary of Contents for Axius 350

Reviews:

Related manuals for Axius 350

Brands by name

Popular brands

MerCruiser Axius 350, Instruction Manual

Search results

Summary of Contents for Axius 350

Reviews:

Related manuals for Axius 350

Brands by name

Popular brands