MerCruiser Axius 350 Instruction Manual Download Page 81 | Manualshive

Page: 81 / 149

background image

Section 3 - On The Water

90-8M0053363

eng

NOVEMBER 2010

Page 73

Axius Shift Override—Emergency Procedure

If the VesselView display shows the error message "GEAR POS DIFF" and an engine will not start or will not shift into gear, there

is a problem with the Electronic Shift Control (ESC) system. If one drive is working, you may operate on one engine and drive.

!

CAUTION

Using the emergency procedure to manually shift the drive disengages shift control at the helm. To avoid damage or injury, drive

cautiously when a gear is engaged manually. To stop the drive and its propeller, you must turn the key switch to the off position.

You can disengage the shift actuator to manually shift the drive into neutral for starting and into forward gear position for operation.

Engine speed will be limited to 1000–1200 RPM while operating in emergency shift override.
To disengage the shift actuator:
1. Turn the ignition switch to the off position and engage the emergency lanyard, if equipped.

!

WARNING

Engine components and fluids are hot and can cause serious injury or death. Allow the engine to cool before removing any

components or opening any fluid hoses.

2. Unplug the shift actuator wiring harness connector.
3. Move the shift lever into the neutral position. The shift actuator is in the neutral position when the shift lever is straight up and

the shift interrupt switch is fully engaged.

a -

Harness

b -

Shift lever

c -

Shift lever in neutral

position

d -

Shift lever in forward

position

e -

Shift lever in reverse

position

f -

Gear position indicator

switch

4. With the drive in neutral, place the ERC into the neutral (idle) position.
5. Reset the lanyard.

!

WARNING

A spinning propeller, a moving boat, or any solid device attached to the boat can cause serious injury or death to swimmers.

Stop the engine immediately whenever anyone in the water is near your boat.

6. Ensure that no one is in the water near the boat, then start the engine.
7. With the engine running at idle speed, the drive can be shifted into gear and out of gear by manually moving the shift lever.

NOTE: Engine speed will be limited to 1000–1200 RPM while operating in emergency shift override. The Auto Heading feature

using the Axius track pad will still function but is limited to this reduced RPM setting.

IMPORTANT: The boat's stopping distance increases during manual gear engagement operation.

N

F

R

a

b

d

e

32243

f

c

Y

Y

«
...
79
80
81
82
83
...
»

Summary of Contents for Axius 350






















































































































































Reviews:

No comments

Related manuals for Axius 350

Brand: pumpa Pages: 32

Brand: 3W Pages: 20

Neomat A Series

Brand: Nice Pages: 52

Brand: Sumoto Pages: 20

marine TM.5.8TS

Brand: Toyama Pages: 88

Brand: Lenze Pages: 36

MCA10I40 Series

Brand: Lenze Pages: 44

Smart Motor m300

Brand: Lenze Pages: 116

Brand: Lenze Pages: 72

Brand: TCF Pages: 16

Brand: Becker Pages: 24

Brand: O.S. engine Pages: 24

Brand: Honda Pages: 2

Brand: Honda Pages: 32

Brand: Honda Pages: 56

Brand: STEYR MOTORS Pages: 134

Marine Engine 2012 Series

Brand: STEYR MOTORS Pages: 274

Brand: Mitsubishi Pages: 147

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands