MerCruiser Axius 350 Instruction Manual Download Page 143

Page: 143 / 149

Section 7 - Troubleshooting

90-8M0053363

eng

NOVEMBER 2010

Page 135

Symptom

Remedy

The ERC lever controls the engine and drive, but does

not reach wide open throttle.

If the engine only reaches 50% of WOT, check the "DOCKING" button

on the DTS trackpad. Put the handles in neutral and push the button

to disengage, if light is on.
Check VesselView to see if cruise control enabled. Disable cruise

control.
Check for damage to the propeller. Check VesselView for Guardian

fault codes that indicate reduced engine power. If found, contact your

authorized Mercury MerCruiser dealer to ask if the propellers need to

be changed.

The ERC lever controls the engine and drive, but does

not respond in a linear manner.

Check the "TROLL" button on the DTS track pad. Put the handles in

Neutral and push the "TROLL" button to disengage, if light is on.
Check whether dock mode or cruise control are on. If on, turn off or

disengage.

When one ERC lever is moved, both engines respond.

Check the "1 LEVER" button on the DTS track pad. If the light is on,

put the handles in neutral and push the "1 LEVER" button to

disengage.

The ERC control, joystick, and steering wheel do not

function.

Press "HELM" on DTS track pad to restore helm control. (Multiple

helm boats only.)

Steering System

Symptom

Remedy

The steering wheel steers the boat, but operates without

resistance.

The starboard key switch is tuned off. Turn on the key.
Check and start the starboard engine.
Check if the starboard harness circuit breaker has tripped. Reset

the circuit breaker, if tripped.

Steering wheel does not steer the boat.

Reduce speed and change to joystick for directional control.
Check steering fluid level and fill if necessary. See

Section 5—

Maintenance

Contact your authorized Mercury MerCruiser dealer.

Steering works, but the boat is not as responsive.

Key off and key on.
Check and start the port engine.
Check the trim tab function.
Check the steering fluid level and fill if necessary. See

Section 5

— Maintenance

Contact your authorized Mercury MerCruiser dealer.

The steering wheel turned past end stop.

Key off and key on to restore steering wheel self‑centering, cruise

control, and to eliminate the fault code.

Power Trim Does Not Operate (Motor Does Not Operate)

Possible Cause

Remedy

Blown fuse.

Replace fuse. Fuses may be located near the dash trim switch, at the trim pump, in the positive

(red) power trim battery lead near the battery switch, or a combination of these.

Loose or dirty electrical

connections or damaged

wiring.

Check all associated electrical connections and wires (especially battery cables). Clean and

tighten faulty connection. Repair or replace wiring.

Summary of Contents for Axius 350






















































































































































Search results

Summary of Contents for Axius 350

Reviews:

Related manuals for Axius 350

Brands by name

Popular brands

MerCruiser Axius 350, Instruction Manual

Search results

Summary of Contents for Axius 350

Reviews:

Related manuals for Axius 350

Brands by name

Popular brands