MerCruiser Axius 350 Instruction Manual Download Page 73

Page: 73 / 149

Section 3 - On The Water

90-8M0053363

eng

NOVEMBER 2010

Page 65

NOTE: The joystick must move over 50% of its travel for the movement to be recognized as input.

24707

Adjusting heading to starboard

To Resume a Heading

The "RESUME" button light is on if the previous course heading is available to resume.
IMPORTANT: The previous heading can only be resumed within one minute of Auto Heading being disengaged or if the boat has

not turned more than 180°.
Press the "RESUME" button to resume the previous heading if you:
•

Turned the steering wheel and disengaged Auto Heading.

•

Pressed one of the "TURN" (course adjust) buttons with Auto Heading engaged.

a -

Port "TURN" button

b -

Starboard "TURN" button

c -

"RESUME" button

d -

"AUTO HEADING" button

Disengaging Auto Heading

1. Disengage the Auto Heading mode with any of the following actions:

•

Place the ERC handles for both engines in neutral. The "AUTO HEADING" button light turns off and the Standby light

comes on.

•

Turn the steering wheel beyond the electronic detent. The "AUTO HEADING" button light turns off and the Resume light

comes on.

35568

Summary of Contents for Axius 350






















































































































































Search results

Summary of Contents for Axius 350

Reviews:

Related manuals for Axius 350

Brands by name

Popular brands

MerCruiser Axius 350, Instruction Manual

Search results

Summary of Contents for Axius 350

Reviews:

Related manuals for Axius 350

Brands by name

Popular brands