MerCruiser Axius 350 Instruction Manual Download Page 71 | Manualshive

Page: 71 / 149

background image

Section 3 - On The Water

90-8M0053363

eng

NOVEMBER 2010

Page 63

Disengaging (Deactivating) Skyhook

IMPORTANT: Under most circumstances, both engines and drives must be operational to achieve acceptable Skyhook

performance. If the necessary reference signals from an engine or drive become unavailable, Skyhook automatically

disengages.
1. To disengage the Skyhook, you must do one of the following:

•

Press the "SKYHOOK" button on the Axius Premier CAN Trackpad.

•

Move any ERC lever out of neutral.

•

Move the joystick.

NOTE: In each method, the light on the Axius Premier CAN Trackpad for the "SKYHOOK" button will turn off.

Auto Heading

Auto Heading allows the boat to automatically maintain a compass heading while the boat is underway.

Engaging Auto Heading

1. Place at least one running engine in forward gear.

NOTE: Auto Heading does not function with the ERC levers in neutral or reverse.

2. Steer the boat to the desired compass heading.
3. Press the "AUTO HEADING" button to engage the Auto Heading mode. The button illuminates and a single horn beep sounds

acknowledging engagement. A double horn beep sounds if Auto Heading does not engage.

a -

Port "TURN" button

b -

Starboard "TURN" button

c -

"RESUME" button

d -

"AUTO HEADING" button

4. Display the Track Waypoint screen on VesselView. See

Mode Display

in

VesselView

.

5. On the VesselView screen for track waypoint, the mode indicator changes from "OFF" to "AUTO".
6. The steering wheel will self‑center and be held in an electronic detent position.

NOTE: If for any reason, you must turn the steering wheel, you will need to apply sufficient force to overcome the electronic

detent.

7. Axius Premier holds the compass heading the boat was following when the "AUTO HEADING" button was pressed and Auto

Heading engaged.

35568

a

b

c

d

«
...
69
70
71
72
73
...
»

Summary of Contents for Axius 350






















































































































































Reviews:

No comments

Related manuals for Axius 350

Brand: Westerbeke Pages: 86

Brand: RHINO MOTION CONTROLS Pages: 4

Brand: Grundfos Pages: 13

Brand: Teryair Pages: 13

Brand: Inel Pages: 4

Brand: Graco Pages: 30

Brand: Grizzly Pages: 2

Brand: DJ ENGINE Pages: 9

Brand: YS Performance Pages: 2

Brand: Yanmar Pages: 184

Brand: Detroit Diesel Pages: 83

Brand: Yanmar Pages: 84

Brand: Sanyo Denki Pages: 20

Brand: MULTIPLEX modell Pages: 11

Brand: Stober Pages: 48

Brand: Baumuller Pages: 26

Brand: Baumuller Pages: 33

Brand: Johnson Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands