MerCruiser Axius 350 Instruction Manual Download Page 36

Page: 36 / 149

Section 2 - Getting to Know Your Power Package

Page 28

90-8M0053363

eng

NOVEMBER 2010

1. A circuit breaker protects the engine wiring harness and the instrumentation power lead. Test the circuit breaker by pushing

the red button. To reset the breaker, push the yellow lever back into the housing.

a -

Yellow lever—shown tripped

b -

Red test button

2. A 90 amp fuse is located on the large post of the starter solenoid. This fuse protects the engine wiring harness if an electrical

overload or a reversed battery condition occurs.

mc74907-1

3. Four fuses are located on the port side of the engine. These fuses protect various Electronic Fuel Injection (EFI) circuits.

mc77602-1

NOTE: The main power and fuel pump relays are located next to the fuses and control voltage to the engine with the ignition

key in the on position.

mc77602-2

22529

Summary of Contents for Axius 350






















































































































































Search results

Summary of Contents for Axius 350

Reviews:

Related manuals for Axius 350

Brands by name

Popular brands

MerCruiser Axius 350, Instruction Manual

Search results

Summary of Contents for Axius 350

Reviews:

Related manuals for Axius 350

Brands by name

Popular brands