Meler PS 20 NON STOP+, Instruction Manual

Page: 44 / 100

FOCKE MELER GLUING SOLUTIONS
4-18
MELTER OPERATION
Operating mode with internal pumping control and external speed control
In this operating mode, the user manually controls the start-up and shutdown
of the pump. Speed is controlled by means of an external 0-10 V signal sent
from the main machine.
The ‘External reference’ option must be activated and the ‘External
permission’ option must be deactivated.
Follow the steps below to use this operating mode:
1. On the start screen, press the pump status icon to access the Pumping
Control menu.
2. On the Pumping Control menu, press the pump that you want to start
up. When the key is green, the pump is activated. When it is grey, the
pump is off.
The following conditions must be met for the pump to start operating:
• The unit must be at ‘Temperature OK’.
• The ‘Pumping permission delay’ time must have elapsed.
• If ‘Pumping safety’ is activated, pumping must be enabled with the
‘STOP’ button (red LED off).
• There must be no alarms preventing pumping.
The system will wait for the speed signal from the main machine.
When this is received, the pump will start rotating at the set speed. The
actual rotation speed is shown on the display.
3. To set the rotation speed to the necessary value for the application,
change the ramp speed (see the ‘Configuring ramp speed’ section).
Together with the ramp speed graph, the display shows the voltage
being delivered from the main machine at that moment.
The pump will stop whenever:
• The control board is disabled using the ON/OFF button.
• The pumping ‘STOP’ button is pressed (red LED is lit).
• When a variator error signal is activated.
• When the MAXIMUM RPM alarm is activated.
• When the MINIMUM RPM alarm is activated.
4. If the unit has a rear switch connector (optional), pumping can also
be activated from the device associated with this connector. Both the
pumping button and switch must be connected to allow the pump to be
activated.
When the LED is green, the contact is closed and the pump can be
started up; when it is red, the contact is open and the pump will remain
off.
HMI : S02001100 v1.0.106
TC : S02200100 v1.0.084
IO : S02102100 v1.0.106
IO : S02101100 v1.0.106
160 154
B
15:35
°C
08:31
2
00
154
1
85
1 2
B
A
VP
160
A
185 170 1
154 154 2
100 100
3
--- --- 4
5
42 42 6
1
3
HMI : S02001100 v1.0.106
TC : S02200100 v1.0.084
IO : S02102100 v1.0.106
IO : S02101100 v1.0.106
50 rpm
50 rpm
Real speed: 73 rpm
External reference 1
External permission 1
Switch 1
Real speed: 76 rpm
External reference 2
External permission 2
Switch 2
PUMP 1
PUMP 2
2
3
HMI : S02001100 v1.0.106
TC : S02200100 v1.0.084
IO : S02102100 v1.0.106
IO : S02101100 v1.0.106
50 rpm
50 rpm
Real speed: 73 rpm
External reference 1
External permission 1
Switch 1
Real speed: 76 rpm
External reference 2
External permission 2
Switch 2
PUMP 1
PUMP 2
4
HMI : S02001100 v1.0.106
TC : S02200100 v1.0.084
IO : S02102100 v1.0.106
IO : S02101100 v1.0.106
160 154
B
15:35
°C
08:31
2
00
154
1
85
1 2
B
A
VP
160
A
185 170 1
154 154 2
100 100
3
--- --- 4
5
42 42 6
HMI : S02001100 v1.0.106
TC : S02200100 v1.0.084
IO : S02102100 v1.0.106
IO : S02101100 v1.0.106
160 154
B
15:35
°C
08:31
2
00
154
1
85
1 2
B
A
VP
160
A
185 170 1
154 154 2
100 100
3
--- --- 4
5
42 42 6
HMI : S02001100 v1.0.106
TC : S02200100 v1.0.084
IO : S02102100 v1.0.106
IO : S02101100 v1.0.106
75 rpm
50 rpm
50 rpm
49 rpm
53 rpm
PUMP 1
Real speed:
External reference 1
External permission 1
Switch 1
Real speed:
External reference 2
External permission 2
Switch 2
PUMP 2
HMI : S02001100 v1.0.106
TC : S02200100 v1.0.084
IO : S02102100 v1.0.106
IO : S02101100 v1.0.106
50 rpm
50 rpm
Real speed: 73 rpm
External reference 1
External permission 1
Switch 1
Real speed: 76 rpm
External reference 2
External permission 2
Switch 2
PUMP 1
PUMP 2
4
4
HMI : S02001100 v1.0.106
TC : S02200100 v1.0.084
IO : S02102100 v1.0.106
IO : S02101100 v1.0.106
3,5 V
0 100 50
0
10
5
Volt rpm
1
0,0 0
2
3,0 20
3
4,0 50
4
7,0 60
5
10 100
Pumping
Analog input
3